AVE MV DR4000 manual Change Pan/Tilt/Zoom Setting

Page 82

13.4 Change Pan/Tilt/Zoom Setting

Please follow the steps provided below to control the Pan/Tilt/Zoom setting through the network as and when necessary.

1. Click the button on the home page to open the Speed Dome Controller.

2.Click the button to control the Zoom setting on the Speed Dome Controller.

3.The right-hand set, , has four buttons, each of which, upon being clicked, will turn the camera all the way, without stopping, in one of the four designated directions. The fifth button, in the center, will stop the camera at any point you prefer.

4.The left-hand set of buttons, , has four buttons, each of which, upon being clicked, will move one short step only in any of the four designated directions.

5.Select a Speed Dome device Model from the drop-down list on the SpeedDome Controller. The Controller will be able to display the Model by turn.

6.Select a Speed Dome device ID from the drop-down list on the Speed Dome

Controller. The Controller will be able to display the ID by turn.

7.

Each of the ten buttons under ‘Set’ is connected with a specific position and angle of either panning or tilting of the camera. Click each button to activate its particular position and angle. Press the button under ‘Preset‘ to turn the camera angle by angle in the set positions.

Each of the ten buttons under ‘Clear’ can be clicked to delete the corresponding ‘Set’ button above it. For example, if you wish to de-activate ‘Set’ button #4, please click ‘Clear’ button #4 to delete its corresponding ‘Set’ counterpart.

Each of the ten buttons designated ‘Go to’ can be clicked to view the particular corresponding angle of the position in which it is set.

80

Image 82
Contents AVE Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionHard-disk drive compartment Front ViewHard disk compartment lock Display button Rec IndicatorDisk Indicator Up / Down CH2 / CH1 buttonsJog Dial Mobile Rack Power LEDMobile Rack HDD LED Rear View Between 75Ω and Hi-ZThis Figure is Looked from the Rear View Alarm In/OutRecord in Input This pin Basic Connection Connecting with 1 to 4 CamerasAttaching AN External Device to DVR Seagate Hard-Disk Drive InstallationMaxtor 09- 05-2003 System Information and channel selectionSystem Information Quality Best Ntsc Rate 6 HR Size POSUpdating System Software Ntsc Audio on Configuring Recording SettingsNtsc Audio OFF PAL Audio OFFPAL Audio on Recording Operations Timer RecordingManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000Alarm / Motion ALM Operation REC Rate Alarm / Motion RecordingPRE- Alarm OFF Motion Setting Main Alarm REC Enable REC Quality Best Audio OFF ALM Type ALM DurationExternally triggered Recording BelowFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations Search to play back a particular recorded videoPlayback Picture-by-picture Slow Forward/ ReversePlay Back Recorded Video from a HDD of the mobile rack Search Operations Search Full List Alarm List Time Search Thumbnail SD CardFull List Search Alarm list Search Time SearchSD Card Search Thumbnail SearchMM DD Year 03 / 13 Set HD 2 to Backup first. Take the following steps Backup OperationsMobile Rack HD Backup Operations F0000.JPG F0001.JPG F0002.JPG F0003.JPG F0004.JPG F0005.JPGFull Select Duplicate a particular recorded video from HD1 to HD2Disk Setting Reformat HD2 Usage Security Digital Card SD Card Backup OperationsSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Transfer the system setting info of DVR to another For more detail Backup the System setting info into SD CardSave the whole setting into the SD card Archive video of AVI Clips into SD CardKey Lock Operation Set Up Menu Navigation Buttons Setup button Enter buttonREC Setting REC QualityAlarm / Motion Setting ALM Type PRE- Alarm 0600-1600 1200-1800 REC Schedule0600-1800 0000-0000 Channel 1 2 3 Dwell 03 03 03 03 TitleNET Enable OFF NET Dhcp NET IP SET FTP Setting Main NET Enable1 S Http Port FTP SettingComm Setting Comm ID Account SET Main SET FTP on / OFFUser AccountFTP Account FTP IP PathBackup HD HD2 Usage HD 1System Situation MAC 00 0c 0c 00 00 Bios Date Mar 10 General Command Format SetupCommunication Protocol Request Time Second Category=0x02 Value of a specific front panel keyDEC HEX Set Time Second Category=0x02DVR Playback Error REC ModeNon REC Mode Request State Second Category=0x06Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack HDD Installation Page Page System Default Disk Setting Reformat SET RS232 / RS485D. Message Meanings Network Viewer PIN noInstall the Network Viewer for the ZIP file View the 4CH DVR video from a remote PC Page Function Buttons Description Page Set the Alarm record settings Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Record ScheduleArchive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConnect to a computer Physical specification of RJ-45 cable for EthernetCable Connections Connect to a LAN Hub IntranetEnable DVR Network Function RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Connect to WAN InternetEnable Dhcp Function Set IP AddressPage 12.3 TCP/IP Communication Software 12.4 TCP/IP installation 12.5 TCP/IP Configuration setting Click Start Settings Control Panel NetworkConnection Testing Click Start ProgramsPage Connecting the 4CH DVR Description of functional keysBrowsing images from the 4CH DVR Page Change Record / Alarm Setting Change Timer Record Setting Change Pan/Tilt/Zoom Setting Page Design and specifications subject to change without notice Model Number MV-DR4000Appendix 1. -SCANIP