AVE MV DR4000 manual Rear View, Between 75Ω and Hi-Z

Page 10

2.2 Rear View

25

26

28

IN

 

 

 

 

 

 

hi-z

OUT

 

 

 

 

 

 

75

CH1

CH2

CH3

CH4

 

 

 

RS-485

 

 

IN

 

 

 

 

ETHERNET

 

 

OUT

 

MONITOR

AUDIO

 

 

RS-232

ALARM I/O

DC12V

 

29

30

31

32

33

34

35

36 37

VIDEO IN Connector: These 4 BNC connectors are used to connect the video output from a camera

Hi-Z/75 Ω Individual termination: These 4 switches are used to set the impedance of each loop

between 75Ω and Hi-Z.

RS-232Port: The RS-232 communication port functions as a connector to an external control device. Please refer to RS-232 & RS-485 Protocol for more details.

MONITOR Connector: The connector provides the unit’s composite video to a display device.

AUDIO OUT: This connector is used to connect the device’s audio input.

AUDIO IN Connector: This connector is used to connect the audio output from a camera or other devices to the DVR.

ETHERNET 10/100 Connector: This is one standard RJ-45 connector for 10/100 Mbps Ethernet networks.

RS-485Port: The RS-485 communication ports function as connectors when two or more units are serially connected to an external control device.

ALARM I/O: This is a 9-PIND-SUB connector including SWITCH OUT, GROUND, ALARM OUT, DISK FULL, RECORD IN, ALARM RESET, and ALARM IN for connecting with external devices. Please refer to the next section for details.

Wire Catch: The wire catch secures the power cord and keeps it in place (so that it does not droop or hang loosely).

Ground Screw’s: The ground screw is for chassis terminal.

DC Power Jack: The inlet connects to the external power supply. 12 VDC, 5A UL Listed Class 2 Power Supply.

8

Image 10
Contents AVE Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionHard-disk drive compartment Front ViewHard disk compartment lock Display button Rec IndicatorDisk Indicator Up / Down CH2 / CH1 buttonsJog Dial Mobile Rack Power LEDMobile Rack HDD LED Rear View Between 75Ω and Hi-ZThis Figure is Looked from the Rear View Alarm In/OutRecord in Input This pin Basic Connection Connecting with 1 to 4 CamerasAttaching AN External Device to DVR Seagate Hard-Disk Drive InstallationMaxtor 09- 05-2003 System Information and channel selectionSystem Information Quality Best Ntsc Rate 6 HR Size POSUpdating System Software Ntsc Audio on Configuring Recording SettingsNtsc Audio OFF PAL Audio OFFPAL Audio on Recording Operations Timer RecordingManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000Alarm / Motion ALM Operation REC Rate Alarm / Motion RecordingPRE- Alarm OFF Motion Setting Main Alarm REC Enable REC Quality Best Audio OFF ALM Type ALM DurationExternally triggered Recording BelowFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations Search to play back a particular recorded videoPlayback Picture-by-picture Slow Forward/ ReversePlay Back Recorded Video from a HDD of the mobile rack Search Operations Search Full List Alarm List Time Search Thumbnail SD CardFull List Search Alarm list Search Time SearchSD Card Search Thumbnail SearchMM DD Year 03 / 13 Set HD 2 to Backup first. Take the following steps Backup OperationsMobile Rack HD Backup Operations F0000.JPG F0001.JPG F0002.JPG F0003.JPG F0004.JPG F0005.JPGFull Select Duplicate a particular recorded video from HD1 to HD2Disk Setting Reformat HD2 Usage Security Digital Card SD Card Backup OperationsSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Transfer the system setting info of DVR to another For more detail Backup the System setting info into SD CardSave the whole setting into the SD card Archive video of AVI Clips into SD CardKey Lock Operation Set Up Menu Navigation Buttons Setup button Enter buttonREC Setting REC QualityAlarm / Motion Setting ALM Type PRE- Alarm 0600-1600 1200-1800 REC Schedule0600-1800 0000-0000 Channel 1 2 3 Dwell 03 03 03 03 TitleNET Enable OFF NET Dhcp NET IP SET FTP Setting Main NET Enable1 S Http Port FTP SettingComm Setting Comm ID Account SET Main SET FTP on / OFFUser AccountFTP Account FTP IP PathBackup HD HD2 Usage HD 1System Situation MAC 00 0c 0c 00 00 Bios Date Mar 10 General Command Format SetupCommunication Protocol Request Time Second Category=0x02 Value of a specific front panel keyDEC HEX Set Time Second Category=0x02DVR Playback Error REC ModeNon REC Mode Request State Second Category=0x06Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack HDD Installation Page Page System Default Disk Setting Reformat SET RS232 / RS485D. Message Meanings Network Viewer PIN noInstall the Network Viewer for the ZIP file View the 4CH DVR video from a remote PC Page Function Buttons Description Page Set the Alarm record settings Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Record ScheduleArchive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConnect to a computer Physical specification of RJ-45 cable for EthernetCable Connections Connect to a LAN Hub IntranetEnable DVR Network Function RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Connect to WAN InternetEnable Dhcp Function Set IP AddressPage 12.3 TCP/IP Communication Software 12.4 TCP/IP installation 12.5 TCP/IP Configuration setting Click Start Settings Control Panel NetworkConnection Testing Click Start ProgramsPage Connecting the 4CH DVR Description of functional keysBrowsing images from the 4CH DVR Page Change Record / Alarm Setting Change Timer Record Setting Change Pan/Tilt/Zoom Setting Page Design and specifications subject to change without notice Model Number MV-DR4000Appendix 1. -SCANIP