AVE MV DR4000 manual ALM Type

Page 37

ALM TYPE:

This option allows users to set a type of alarm input corresponding to the sensor signal in use.

NO: Normally Open. This is to be used with the type of alarm sensor whose contact remains open in normal conditions and closes in case of activation.

NC: Normally Closed. This is to be used with the type of alarm sensor whose contact remains closed in normal conditions and opens in case of activation.

ALM DURATION:

This option allows users to set alarms for a certain duration. You can select one of the six following options: 0 SEC, 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP.

Duration Set ting

 

 

Alarm recording

 

 

 

 

 

Duration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Alarm

Alarm

 

 

activated

deactivated

 

 

Non-Stop

Alarm recording

 

 

 

 

 

 

 

 

 

Duration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Alarm

Alarm

 

Reset

activated

deactivated

 

 

NOTE: Recording may be interrupted at the time of Alarm-in or Alarm-out. LIVE images may be interrupted at the time of Alarm-out.

35

Image 37
Contents AVE Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesHard-disk drive compartment Front ViewHard disk compartment lock Disk Indicator Rec IndicatorDisplay button Up / Down CH2 / CH1 buttonsJog Dial Mobile Rack Power LEDMobile Rack HDD LED Between 75Ω and Hi-Z Rear ViewThis Figure is Looked from the Rear View Alarm In/OutRecord in Input This pin Basic Connection Connecting with 1 to 4 CamerasAttaching AN External Device to DVR Seagate Hard-Disk Drive InstallationMaxtor 09- 05-2003 System Information and channel selectionSystem Information Size POS Quality Best Ntsc Rate 6 HRUpdating System Software Ntsc Audio OFF Configuring Recording SettingsNtsc Audio on PAL Audio OFFPAL Audio on Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 WPRE- Alarm OFF Motion Setting Main Alarm REC Enable Alarm / Motion RecordingAlarm / Motion ALM Operation REC Rate REC Quality Best Audio OFF ALM Type ALM DurationBelow Externally triggered RecordingPlayback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse Search to play back a particular recorded videoPlayback Picture-by-picture Slow Forward/ ReversePlay Back Recorded Video from a HDD of the mobile rack Search Operations Search Full List Alarm List Time Search Thumbnail SD CardFull List Search Time Search Alarm list SearchSD Card Search Thumbnail SearchMM DD Year 03 / 13 Mobile Rack HD Backup Operations Backup OperationsSet HD 2 to Backup first. Take the following steps F0000.JPG F0001.JPG F0002.JPG F0003.JPG F0004.JPG F0005.JPGSelect Duplicate a particular recorded video from HD1 to HD2 FullDisk Setting Reformat HD2 Usage Security Digital Card SD Card Backup OperationsSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Save the whole setting into the SD card For more detail Backup the System setting info into SD CardTransfer the system setting info of DVR to another Archive video of AVI Clips into SD CardKey Lock Operation Enter button Set Up Menu Navigation Buttons Setup buttonREC Quality REC SettingAlarm / Motion Setting ALM Type PRE- Alarm 0600-1600 1200-1800 REC Schedule0600-1800 0000-0000 Title Channel 1 2 3 Dwell 03 03 03 03NET Enable NET Enable OFF NET Dhcp NET IP SET FTP Setting MainComm Setting Comm ID Http Port FTP Setting1 S Account SET Main SET FTP on / OFFFTP Account FTP IP AccountUser PathHD 1 Backup HD HD2 UsageSystem Situation MAC 00 0c 0c 00 00 Bios Date Mar 10 General Command Format SetupCommunication Protocol DEC HEX Value of a specific front panel keyRequest Time Second Category=0x02 Set Time Second Category=0x02Non REC Mode REC ModeDVR Playback Error Request State Second Category=0x06Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack HDD Installation Page Page System Default SET RS232 / RS485 Disk Setting ReformatD. Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the 4CH DVR video from a remote PC Page Function Buttons Description Page Set the regular record settings Change the Record & Timer Properties Via the NetworkSet the Alarm record settings Set the Record ScheduleArchive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Cable Connections Physical specification of RJ-45 cable for EthernetConnect to a computer Connect to a LAN Hub IntranetConfigure Your DVR Network Settings RJ-45 PIN configuration for LAN HubEnable DVR Network Function Connect to WAN InternetSet IP Address Enable Dhcp FunctionPage 12.3 TCP/IP Communication Software 12.4 TCP/IP installation Click Start Settings Control Panel Network 12.5 TCP/IP Configuration settingClick Start Programs Connection TestingPage Description of functional keys Connecting the 4CH DVRBrowsing images from the 4CH DVR Page Change Record / Alarm Setting Change Timer Record Setting Change Pan/Tilt/Zoom Setting Page Model Number MV-DR4000 Design and specifications subject to change without noticeAppendix 1. -SCANIP