SterlingTEK A0551797 manual Water-Cooled SSC Series Startup

Page 35

þCheck the water level in the pump tank to be sure the pump does not run dry while the system piping is being filled.

þCheck your work and proceed to the Startup procedure.

5-3 Water-Cooled SSC Series Startup

1.Start the chiller by pushing the Start button on the control panel of the unit.

2.The touchscreen will display the Main Menu screen.

3.If your chiller has been setup to control the pump tank, the recirculation pump will turn on first, then after 5 seconds the process pump will turn on. If configured with a standby pump, the lead/lag will control which pump turns on.

4.Fifteen (15) seconds after the last pump turns on the first compressor will turn on. Based on the temperature of the water the controller will turn on compressors every 15 seconds.

5.Adjust the Freezestat cut-out, located in the main electrical enclosure, to 10°F (6ºC) below the process temperature set point you want.

Note: If the recirculation pump does not turn on (or that the flow switch is not satisfied) the compressors will not be allowed to turn on.

6.Check the pump(s) amp draws and pressures. The amp draws must be within the pump(s) running load and service factor amps.

7.Operate the chiller, looking for leaks and listening for unusual noises or vibrations that could indicate improper operation.

5-4 Remote Air-Cooled SSC Series Startup Checklist

þCheck the shipping papers against the serial tag to be sure chiller size, type and voltage is correct for the process.

þCheck the transformer primary voltage connections to be sure they are configured for the electrical power you are using.

þThe voltage at the main power connection must read within plus or minus ten percent (±10%) of the voltage listed on the serial tag.

þPhase imbalance must be less than two percent (<2%).

SSC Series Central Chilling Stations

Page 35 of 86

Image 35

Contents SSC Series Central Chilling Stations SSC Series Central Chilling Stations Wear Safety Glasses and Work Gloves Safety ConsiderationsTable of Contents Getting Started on the SSC Series Advanced Touchscreen Startup ChecklistsCharts and Figures Necessary Documents IntroductionModels Covered Standard FeaturesAvailable Options Standard Features on Remote CondensersModel Number Nomeclature Model SSCW-xxx Typical Two-Circuit 60-100 Ton Water Cooled ChillerCooling Capacity tons @ 50F 10 C LWT 73.1 81.4 Model SSCR-xxx Typical Two-Circuit 60-100 Ton Remote Air Cooled ChillerSscr Series Remote Condenser Models Event of Shipping Damages Unpacking and InspectionReturns If the Shipment is Not CompleteIf the Shipment is Not Correct Uncrating Your New Chiller SSC Series Central Chilling Stations Making Electrical Connections 3InstallationInstallation Location Considerations SSC Series Central Chilling Stations All Models Piping ConsiderationsMaking Process Water Connections From Process Making Tank Piping ConnectionsMaking Water-Cooled Condenser Connections Water Connection Sizing ConsiderationsGalvanic Corrosion Considerations Water Treatment ConsiderationsCondenser Water Installing the Remote Air-Cooled CondenserCompressor Checking Motor DirectionSSC Series Central Chilling Stations Lead-Lag Pumps AlarmsStaging Lead-Lag CompressorsFreezestat Control Chilled Water CircuitRefrigeration Circuit Freezing Protection Curve VolumeLow Pressure Cutout Flow SwitchHigh Pressure Cutout Condenser Water Manifold Control NippleControl Probe Chilled Water ManifoldSSC Series Central Chilling Stations Water-Cooled SSC Series Startup Checklist Startup ChecklistsSSC Series Central Chilling Stations Water-Cooled SSC Series Startup Remote Air-Cooled SSC Series Startup ChecklistSSC Series Central Chilling Stations Remote Air-Cooled SSC Series Startup Shutdown Determining Flow RateSSC Series Central Chilling Stations SSC Series Central Chilling Stations Graphic Panel Devices Indicator Lights and Control Switches MMISSC Series Central Chilling Stations Touchscreen Interface Introduction MMI Using the StandardTouchscreen Interface SSC Series Standard Control Panel Using the SSC Series Standard Touchscreen InterfaceMain Menu Screen Compressor Status Screen Viewing and Operating Chiller CompressorsViewing Compressor Status Operating the chiller compressors Chiller Configuration ScreenCompressor Lead/Lag Screen Compressor Enable ScreenCompressor Run Time Display Screen Viewing Compressor Run TimesPump Status Screen Viewing and Operating Chiller PumpsViewing Chiller Pump Status Operating Chiller Pumps Pump Enables ScreenPump Run Time Display Screen Viewing Pump Run TimesPump Lead/Lag Screen Alarm Condition Screen Viewing Active Alarms and Handling Alarm ConditionsOr Death Setting System Temperatures Viewing and Setting System TemperaturesSSC Series Central Chilling Stations Using the Advanced Using the SSC Series Advanced Touchscreen Interface Main Menu Screen Viewing and Operating Chiller Compressors Chiller Status Screen Operating the chiller compressors Viewing Compressor Run Times Viewing and Operating Chiller Pumps Viewing Chiller Pump Status Operating Chiller Pumps Hourmeters Pump Run Time screen displays Viewing Active Alarms and Handling Alarm Conditions Alarm Condition Screen Or Death System Status Screen Temperature Input Display Screen Lubrication Condenser MaintenanceRecommended Pump Tank Spare Parts Evaporator MaintenancePump Motor Seal Makeup ValvePreventive Maintenance Service SSC Series Central Chilling Stations Problem Possible Cause Solution 10TroubleshootingAllow time to cool and reset Verify proper rotation if Service Notes Index Water Treatment Service Notes Service Notes Service Notes Sterling Th Street New Berlin, WI 262 641-8610 ∙ Fax 262 Parts Department