Zebra Technologies P1071336-002 manual Weblink.ip.conn12.enable

Page 52

52

WebLink Set/Get/Do Commands

weblink.ip.conn[12].enable

weblink.ip.conn[12].enable

Description This command enables or disables the weblink IP connection #1.

A side effect of setting this SGD to "on", the weblink.enable will also be set to "on". When this setting is set to "off", if the weblink.ip.conn2.enable is also "off", the weblink.enable will be set to "off".

Supported Devices

•iMZ 220™, iMZ 320™

•QLn220™, QLn320™, QLn420™

•ZT210™, ZT220™, ZT230™

Type setvar, getvar

Commands	Details

setvar	This command enables/disables the weblink IP connection.
	Format:
	•	! U1 setvar "weblink.ip.conn1.enable" "value"
	•	! U1 setvar "weblink.ip.conn2.enable" "value"
	Values: "on", "off"
	Default: "off"

getvar	This command retrieves the current setting.

Format:

•! U1 setvar "weblink.ip.conn1.enable"

•! U1 setvar "weblink.ip.conn2.enable"

Result:

•"on" if the connection is enabled

•"off" if the connection is disabled

P1071336-002

1/20/15

Image 52

Contents Soti Page 20/15 P1071336-002 P1071336-002 20/15 Contents WebLink Set/Get/Do Commands About This Document Who Should Use This Document How This Document Is OrganizedDocument Conventions Icons UsedAbout This Document Introduction What Soti MobiControl Connector Does OverviewSupported Printers Supported Operating SystemsInstallation Installing in a Windows Operating System Minimum System RequirementsInstallation Steps Install a MobiControl ServerInstallation My Documents\zebracerts\ Click Finish Install Software Installation Mypasserver.com Mypc.company.lan Enter the password selected in on Installation Enable Printer Discovery Test a PrinterInstallation Installation Installation Installation Set Up Printers Discover Your Printers Configuring Printers with WebLink Basic Configuration Configuring WeblinkWhen a Proxy Server is Part of the Network Configuration When Http Authentication is Necessary To remove authentication credentials issue the followingEnable Logging Additional Firewall ConfigurationDifference Between Conn1 and Conn2 Navigating the Log Output Configuring Printers with WebLink Troubleshooting Restarting the Soti MobiControl Connector Installation ErrorsLocating the Soti MobiControl Connector Log File SSL/TLS Certificate Errors Value that it was last set to. This does not mean the valueIncorrect. Check that the printer’s date and time rtc.date Other Typical Errors CommunicationTroubleshooting Http Messages Troubleshooting WebLink Set/Get/Do Commands Introduction to SGD Commands Weblink.enable Weblink.ip.conn12.authentication.add Entries Weblink.ip.conn12.authentication.entries Weblink.ip.conn12.authentication.remove Weblink.ip.conn12.enable Weblink.ip.conn12.location Weblink.ip.conn12.maximumsimultaneous connections This command assigns the URL of the connection proxy Weblink.ip.conn12.proxyHttp//usernamepassword@mydomain.com3128 Http//mydomain.com Default Weblink.ip.conn12.retryintervalWeblink.ip.conn12.test.location WebLink Set/Get/Do Commands Weblink.ip.conn12.test.retryinterval Default failure Weblink.ip.conn12.test.testonWebLink Set/Get/Do Commands This command clears the weblink log entires Weblink.logging.clearWeblink.logging.entries Supported DevicesWeblink.logging.maxentries WebLink Set/Get/Do Commands Weblink.printerresetrequired Weblink.restoredefaults This command defaults the weblink branch settings20/15 P1071336-002 Zebra Technologies Europe Limited