Zebra Technologies P1071336-002 manual Weblink.restoredefaults

Page 68

68

WebLink Set/Get/Do Commands

weblink.restore_defaults

weblink.restore_defaults

Description This command defaults, and saves, the weblink branch settings. Any value, including an empty string, will default the weblink branch settings.

Note • The entire weblink branch of settings will be defaulted and the settings are saved; however, the weblink connections will not use the new settings until the printer is restarted (e.g. the weblink.printer_reset_required SGD will be "yes" after a default).

^JUF, ^JUS, ^JUN, ^JUA, and device.restore_defaults do not have any affect on this setting.

 

Supported Devices

 

• iMZ 220™, iMZ 320™

 

QLn220™, QLn320™, QLn420™

 

ZT210™, ZT220™, ZT230™

 

Type setvar, do

 

 

Commands

Details

 

 

setvar

This command defaults the weblink branch settings.

 

Format: ! U1 setvar "weblink.restore_defaults" "value"

 

Values: Any value, including an empty string, will default the branch

 

Default: NA

 

 

do

This command defaults the weblink branch settings.

 

Format: ! U1 do "weblink.restore_defaults" "value"

 

Values: Any value, including an empty string, will default the branch

 

Default: NA

 

 

 

Example • These all default the branch:

!U1 setvar "weblink.restore_defaults" ""

!U1 setvar "weblink.restore_defaults" "foo"

!U1 do "weblink.restore_defaults" ""

!U1 do "weblink.restore_defaults" "foo"

P1071336-002

1/20/15

Image 68
Contents Soti Page 20/15 P1071336-002 P1071336-002 20/15 Contents WebLink Set/Get/Do Commands About This Document Who Should Use This Document How This Document Is OrganizedDocument Conventions Icons UsedAbout This Document Introduction What Soti MobiControl Connector Does OverviewSupported Printers Supported Operating SystemsInstallation Installing in a Windows Operating System Minimum System RequirementsInstallation Steps Install a MobiControl ServerInstallation My Documents\zebracerts\ Click Finish Install Software Installation Mypasserver.com Mypc.company.lan Enter the password selected in on Installation Enable Printer Discovery Test a PrinterInstallation Installation Installation Installation Set Up Printers Discover Your Printers Configuring Printers with WebLink When a Proxy Server is Part of the Network Configuration Configuring WeblinkBasic Configuration When Http Authentication is Necessary To remove authentication credentials issue the followingDifference Between Conn1 and Conn2 Additional Firewall ConfigurationEnable Logging Navigating the Log Output Configuring Printers with WebLink Troubleshooting Locating the Soti MobiControl Connector Log File Installation ErrorsRestarting the Soti MobiControl Connector SSL/TLS Certificate Errors Value that it was last set to. This does not mean the valueIncorrect. Check that the printer’s date and time rtc.date Other Typical Errors CommunicationTroubleshooting Http Messages Troubleshooting WebLink Set/Get/Do Commands Introduction to SGD Commands Weblink.enable Weblink.ip.conn12.authentication.add Entries Weblink.ip.conn12.authentication.entries Weblink.ip.conn12.authentication.remove Weblink.ip.conn12.enable Weblink.ip.conn12.location Weblink.ip.conn12.maximumsimultaneous connections This command assigns the URL of the connection proxy Weblink.ip.conn12.proxyHttp//usernamepassword@mydomain.com3128 Http//mydomain.com Default Weblink.ip.conn12.retryintervalWeblink.ip.conn12.test.location WebLink Set/Get/Do Commands Weblink.ip.conn12.test.retryinterval Default failure Weblink.ip.conn12.test.testonWebLink Set/Get/Do Commands This command clears the weblink log entires Weblink.logging.clearWeblink.logging.entries Supported DevicesWeblink.logging.maxentries WebLink Set/Get/Do Commands Weblink.printerresetrequired Weblink.restoredefaults This command defaults the weblink branch settings20/15 P1071336-002 Zebra Technologies Europe Limited