Kramer Electronics VS-1616SDI user manual All OUTs

Page 26

Operating Your SDI Video Matrix Switcher

2.Press the appropriate IN button.

The MATRIX Display shows the 2 blinking digits, representing the input number and the TAKE LED blinks.

The STATUS Display shows1 the message:

out # x

from in # y

Where x is the output number and y is the input number

3.Press the second appropriate OUT button, repeating step 1 above.

4.Press the appropriate2 IN button, repeating step 2 above.

5.Continue with this OUT-IN button sequence, pressing the appropriate OUT and IN buttons, as required. You can also combine an OUT-OFF or OFF- OUT combination with this sequence.

6.After completing the sequence, press the TAKE button to confirm the actions.

The inputs switch to the respective outputs, as the MATRIX Display shows (no digits blink) and the TAKE LED lights.

7.2.2.3Switching One Input to All Outputs

To switch one input to all the outputs (in the AT ONCE mode):

1.Press the ALL button.

The MATRIX Display shows all the sets of 2 blinking digits (each representing the present input number for that respective output) blinking simultaneously.

The STATUS Display shows the message:

all OUTs

2.Press the appropriate IN button.

This input switches to all the outputs and the MATRIX Display shows the identical non-blinking 2 digits (representing that input number).

To switch one input to all the outputs (in the CONFIRM mode, (the TAKE LED is lit)):

1.Repeat steps 1 and 2 above. The TAKE LED blinks.

2.Press the TAKE button to confirm the action.

The selected input switches to all the outputs and the TAKE LED lights.

1 Continuously, within the limit of the timeout (approximately 30 seconds) 2 That corresponds with the second OUT button

22

KRAMER: SIMPLE CREATIVE TECHNOLOGY

 

Image 26
Contents Model Contents Upgrading Flash Memory Figures TablesOverview IntroductionGetting Started Overview Your SDI Video Matrix Switcher Operating a Single MachineVS-1616SDI 16x16 SDI Video Matrix Switcher Feature Function Installing the SDI Video Matrix Switcher Configuring a Standalone SDI Video Matrix SwitcherAssembling a System of Interconnected Switchers Setting the Dipswitches Assembling a System of Interconnected SwitchersSetting the Machine # Understanding the System Mode Connecting a Control Interface Keyboard LockedConnecting a PC to Four Switchers Connecting with a Null-modem Adapter Null-modem adapter Illustrates the RS-485 line that connects An RS-485 Control Interface Setup Configuring the Sync Connecting the Keyboard ExtensionOperating Your SDI Video Matrix Switcher Using the Startup DisplayUsing the Front Panel Buttons Default Startup Status Display SequenceOut # Where x is the output number Out # From in # yAll OUTs Out # Reset Clearing Several Outputs Reset ALL connections Reset ALL ? Press Take to executeUse two digit # # xy Enter Setup numberStore this Setup ? Using the Menu Command Sequence Setup # xy Load ?Sequence of Menu Commands Locking and Unlocking the Front Panel Choosing the System Modes Follow the System Yes TAKE, next MenuChoosing the Switching Method Setting Understanding the Switching Method Settings Switching Method setting Yes TAKE, next Menu NoVIS 2 EXT 3 INT#1 4MTX ExternalChoosing the Extended Keyboard Setting STO/RCL mode Setting the STORE/RECALL Keyboard ModeSTORE/RECALL setting Yes TAKE, next Menu Changed At onceChoosing the Communication Setting Setting the IR Remote Control Choosing the Auto Store Current Setup Identifying the MachineOutkey 1 Current status Factory default Choosing the Initial ResetInitial Reset Yes TAKE, next Menu Reset to factory default Press Take to executeConnecting the PC to the RS-232 Port Upgrading Flash MemoryUpgrading the Firmware 16608D Ready for receiving Start transmission from PCProgram replaced Technical Specifications Hex CodesHex Table for the VS-1616SDI Video Matrix Switcher #, i# Ascii Protocol GeneralAscii Protocol Description ExampleOK!! or Error Page 2900-002063 REV