Kramer Electronics VS-1616SDI user manual Setting the IR Remote Control

Page 41

Using the MENU Command Sequence

Switcher response

Current:

changed

No reply

8.8Setting the IR REMOTE Control

Set the IR REMOTE control to enable remote control of the VS-1616SDI16x16 Video Matrix Switcher, using the Kramer RC-IR2 Infra-Red Remote Control Device1. Refer to the RC-IR2 Infra-Red Remote Control Device user manual2, for full details. Table 6 and Table 7 summarize the setup and operational commands.

Table 6: Summary of Basic RC-IR2 Setups

To execute this command:

Press the following keys in this sequence:

 

 

Allocate the VS-1616SDIto Group 12

SHIFT + GROUP + 12

Set the MACHINE #

UNIT + # key3 (according to the VS-1616SDIdipswitch settings)

 

 

To enable IR REMOTE control (when set OFF), do the following:

1.Press the MENU button until reaching the IR REMOTE setting. The MATRIX Display shows the message:

IR REMOTE setting

yes -> TAKE, next -> MENU

2. Press the TAKE button.

The Displays show the messages:

 

Outkey 1: InfraredREMOTE OFF

current:

2: InfraredREMOTE ON

remote OFF

3.Press the OUT button 2.

The TAKE LED blinks and the Displays show the messages:

Turn ON infrared REMOTE ?

Current:

Press TAKE to execute

remote OFF

4. Press the TAKE button again.

 

The Displays show the messages:

 

Infrared REMOTE mode

Current:

changed

remote ON

1 After enabling the IR REMOTE control command, remotely control the VS-1616SDI via the IR-1 remote control transmitter pointed at the remote receiver on the VS-1616SDI’s front panel (item 1 in Figure 2)

2 Download up-to-date Kramer user manuals from our Web site at http://www.kramerelectronics.com 3 For example, press UNIT + # 1 if the VS-1616SDI is set as MACHINE # 1

37

Image 41
Contents Model Contents Upgrading Flash Memory Tables FiguresOverview IntroductionGetting Started Overview Operating a Single Machine Your SDI Video Matrix SwitcherVS-1616SDI 16x16 SDI Video Matrix Switcher Feature Function Configuring a Standalone SDI Video Matrix Switcher Installing the SDI Video Matrix SwitcherAssembling a System of Interconnected Switchers Assembling a System of Interconnected Switchers Setting the DipswitchesSetting the Machine # Understanding the System Mode Keyboard Locked Connecting a Control InterfaceConnecting a PC to Four Switchers Connecting with a Null-modem Adapter Null-modem adapter Illustrates the RS-485 line that connects An RS-485 Control Interface Setup Connecting the Keyboard Extension Configuring the SyncUsing the Startup Display Operating Your SDI Video Matrix SwitcherDefault Startup Status Display Sequence Using the Front Panel ButtonsOut # Out # From in # y Where x is the output numberAll OUTs Out # Reset Clearing Several Outputs Reset ALL ? Press Take to execute Reset ALL connectionsUse two digit # # xy Enter Setup numberStore this Setup ? Setup # xy Load ? Using the Menu Command SequenceSequence of Menu Commands Locking and Unlocking the Front Panel Follow the System Yes TAKE, next Menu Choosing the System ModesChoosing the Switching Method Setting Understanding the Switching Method Settings NoVIS 2 EXT 3 INT#1 4MTX External Switching Method setting Yes TAKE, next MenuChoosing the Extended Keyboard Setting STORE/RECALL setting Yes TAKE, next Menu Setting the STORE/RECALL Keyboard ModeSTO/RCL mode Changed At onceChoosing the Communication Setting Setting the IR Remote Control Identifying the Machine Choosing the Auto Store Current SetupInitial Reset Yes TAKE, next Menu Choosing the Initial ResetOutkey 1 Current status Factory default Reset to factory default Press Take to executeUpgrading Flash Memory Connecting the PC to the RS-232 PortUpgrading the Firmware 16608D Ready for receiving Start transmission from PCProgram replaced Hex Codes Technical SpecificationsHex Table for the VS-1616SDI Video Matrix Switcher Ascii Protocol Description Ascii Protocol General#, i# ExampleOK!! or Error Page 2900-002063 REV