Kramer Electronics VS-1616SDI Ready for receiving Start transmission from PC, Program replaced

Page 46

Upgrading Flash Memory

10.After a few seconds the FLASH memory is erased and the MATRIX Display shows the following message:

Ready for receiving

Start transmission from PC

Note: If upgrading the firmware on more than one VS-1616SDI unit, be sure to perform the above steps, 5 to 9, on each VS-1616SDI unit before continuing.

11.From your PC’s K-Senderprogram, click the Send button.

The color of the Send button changes to red and numbers appear dynamically inside the blue line. The Displays on the VS-1616SDIshow the messages:

Transfer may take minutes

￿=0807561

Please, wait…

 

12.Observe the PC monitor and the VS-1616SDIMATRIX and STATUS Displays. After about 30 seconds, the program installation completes, the color of the Send button ceases to be red and the numbers inside the blue line disappear. The Displays on the VS-1616SDIshow the messages:

Program replaced

￿=16608D

successfully!

16608D

13. After about 3 seconds, the Displays show the messages:

Turn unit OFF, reconnect

￿=16608D

cables and turn ON

16608D

14.Verify that the checksum (for example, ￿=16608D) is the same on both lines.

If not, repeat the firmware upgrade process from the beginning.

15.You have successfully replaced the previous program and upgraded to the latest Kramer firmware version.

Turn the POWER switch on the VS-1616SDIoff.

Reconnect the RS-232 IN and RS-232 OUT rear panel port connections (as applicable).

Turn the POWER switch on the VS-1616SDIon again.

Observe the new version number that shows in the STATUS Display. Go to the Menu and restore your specific settings. Prepare and store all necessary setups.

1 Shows the dynamic progress upgrade of the checksum

42

KRAMER: SIMPLE CREATIVE TECHNOLOGY

 

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Model Contents Upgrading Flash Memory Figures TablesGetting Started IntroductionOverview Overview Your SDI Video Matrix Switcher Operating a Single MachineVS-1616SDI 16x16 SDI Video Matrix Switcher Feature Function Installing the SDI Video Matrix Switcher Configuring a Standalone SDI Video Matrix SwitcherAssembling a System of Interconnected Switchers Setting the Dipswitches Assembling a System of Interconnected SwitchersSetting the Machine # Understanding the System Mode Connecting a Control Interface Keyboard LockedConnecting a PC to Four Switchers Connecting with a Null-modem Adapter Null-modem adapter Illustrates the RS-485 line that connects An RS-485 Control Interface Setup Configuring the Sync Connecting the Keyboard ExtensionOperating Your SDI Video Matrix Switcher Using the Startup DisplayUsing the Front Panel Buttons Default Startup Status Display SequenceOut # Where x is the output number Out # From in # yAll OUTs Out # Reset Clearing Several Outputs Reset ALL connections Reset ALL ? Press Take to executeStore this Setup ? Enter Setup numberUse two digit # # xy Using the Menu Command Sequence Setup # xy Load ?Sequence of Menu Commands Locking and Unlocking the Front Panel Choosing the System Modes Follow the System Yes TAKE, next MenuChoosing the Switching Method Setting Understanding the Switching Method Settings Switching Method setting Yes TAKE, next Menu NoVIS 2 EXT 3 INT#1 4MTX ExternalChoosing the Extended Keyboard Setting STO/RCL mode Setting the STORE/RECALL Keyboard ModeSTORE/RECALL setting Yes TAKE, next Menu Changed At onceChoosing the Communication Setting Setting the IR Remote Control Choosing the Auto Store Current Setup Identifying the MachineOutkey 1 Current status Factory default Choosing the Initial ResetInitial Reset Yes TAKE, next Menu Reset to factory default Press Take to executeConnecting the PC to the RS-232 Port Upgrading Flash MemoryUpgrading the Firmware Program replaced Ready for receiving Start transmission from PC16608D Technical Specifications Hex CodesHex Table for the VS-1616SDI Video Matrix Switcher #, i# Ascii Protocol GeneralAscii Protocol Description ExampleOK!! or Error Page 2900-002063 REV
Top Page Image Contents