Kramer Electronics VS-1616SDI Enter Setup number, Use two digit # # xy, Store this Setup ?

Page 30

Operating Your SDI Video Matrix Switcher

7.2.4.1 Storing Setups

 

To store a setting, do the following:

 

1. Press the STO button.

 

The Displays show the messages:

 

Enter SETUP number

Store

use two digit # 01-99

# xy

Where xy are the OUT buttons.

 

2.Press two OUT buttons, using the OUTkeys # 1 to 9, and 10 (for 0). The OUTkeys function on a decimal-basis, and not on a positional-basis. For example, to enter the # 14, press # 1 followed by # 4 (not # 14). To enter the # 3, press # 3 followed by the TAKE button1.

The TAKE LED blinks and the Displays show the messages:

STORE this SETUP ?

Store

YES -> TAKE

# xy

3.Press the TAKE button.

The memory stores the setup and the MATRIX Display shows the message:

Setup # xy stored

Note, saving a setup to an already allocated setup #, prompts the message in the MATRIX Display:

Setup already exists

Press TAKE to overwrite

Pressing the TAKE button replaces the stored setup with the current setup. Alternatively, press a different OUT button to change the setup #.

7.2.4.2 Recalling Setups

 

To recall a setting, do the following:

 

1. Press the RCL button.

 

The Displays show the messages:

 

Enter SETUP number

RECALL

use two digit # 01-99

# xy

where xy are the OUT buttons.

 

2.Press the appropriate two OUT buttons, using the OUTkeys # 1 to 9, and 10 (for 0). The OUTkeys function on a decimal-basis, and not on a positional-

1 Alternatively, pressing # 10 followed by # 3 will also enter the # 3

26

KRAMER: SIMPLE CREATIVE TECHNOLOGY

 

Image 30
Contents Model Contents Upgrading Flash Memory Figures TablesIntroduction Getting StartedOverview Overview Your SDI Video Matrix Switcher Operating a Single MachineVS-1616SDI 16x16 SDI Video Matrix Switcher Feature Function Installing the SDI Video Matrix Switcher Configuring a Standalone SDI Video Matrix SwitcherAssembling a System of Interconnected Switchers Setting the Dipswitches Assembling a System of Interconnected SwitchersSetting the Machine # Understanding the System Mode Connecting a Control Interface Keyboard LockedConnecting a PC to Four Switchers Connecting with a Null-modem Adapter Null-modem adapter Illustrates the RS-485 line that connects An RS-485 Control Interface Setup Configuring the Sync Connecting the Keyboard ExtensionOperating Your SDI Video Matrix Switcher Using the Startup DisplayUsing the Front Panel Buttons Default Startup Status Display SequenceOut # Where x is the output number Out # From in # yAll OUTs Out # Reset Clearing Several Outputs Reset ALL connections Reset ALL ? Press Take to executeEnter Setup number Store this Setup ?Use two digit # # xy Using the Menu Command Sequence Setup # xy Load ?Sequence of Menu Commands Locking and Unlocking the Front Panel Choosing the System Modes Follow the System Yes TAKE, next MenuChoosing the Switching Method Setting Understanding the Switching Method Settings Switching Method setting Yes TAKE, next Menu NoVIS 2 EXT 3 INT#1 4MTX ExternalChoosing the Extended Keyboard Setting STO/RCL mode Setting the STORE/RECALL Keyboard ModeSTORE/RECALL setting Yes TAKE, next Menu Changed At onceChoosing the Communication Setting Setting the IR Remote Control Choosing the Auto Store Current Setup Identifying the MachineOutkey 1 Current status Factory default Choosing the Initial ResetInitial Reset Yes TAKE, next Menu Reset to factory default Press Take to executeConnecting the PC to the RS-232 Port Upgrading Flash MemoryUpgrading the Firmware Ready for receiving Start transmission from PC Program replaced16608D Technical Specifications Hex CodesHex Table for the VS-1616SDI Video Matrix Switcher #, i# Ascii Protocol GeneralAscii Protocol Description ExampleOK!! or Error Page 2900-002063 REV