Enterasys Networks X009-U manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made. The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

2007 Enterasys Networks, Inc. All rights reserved. Part Number: 9034084‐02 February 2007

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, NETSIGHT, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries. All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies Features X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply Replacement X4-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsInstalling and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling and Removing a Fan Tray Installing a Fan TrayFan tray bezel IOM slot Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Connecting Fiber-Optic Cables Removing an XFP/SFP ModuleXFP transceiver Port slot Release handle SFP transceiver MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsConnecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisAC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions Function LED Activity DC Power LEDFan Tray LED Fan Tray LED DefinitionsFunction LED Activity Module LEDs and Reset Button Control and Fabric Module LEDsFabric Module Control Module CM LEDs Only State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM & FM LEDs State LED ActivityEthernet Port LED RX/TX LED Activity First-Time Quick ConfigurationIOM LED Definitions Status LED LED ActivityNaming the Matrix X4-C Configuring DhcpAssigning an IP Address to eth0 Enabling NTPFirst-Time Quick Configuration Matrix X4-C Chassis Setup AC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications SpecificationTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Redundancy Configurations for AC Line 100-240 VacGigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical Specifications 10 µm SMFTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceIndex MT-RJ NTP Index-4