Enterasys Networks X009-U manual Configuration Guidelines

Page 30

Configuration Guidelines

Configuration Guidelines

The Matrix X4‐C chassis provides eight slots that accept modules. IOM (Input/Output Module) slots are numbered 1 through 4 from bottom to top. Two Fabric Module slots, labeled FM1 and FM2, are located in the middle‐left of the chassis, and to their right, Control Module slots CM1 and CM2.

The three slots located at the base of the chassis are reserved for power supplies. Lastly, two Fan Tray slots occupy the right side of the chassis.

2-2 Site and Configuration Guidelines

Image 30
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X4-C Chassis with Redundant Power Supplies Features X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X4-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X4-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X4-C Chassis Setup Required ToolsUnpacking the Matrix X4-C Chassis Shipping straps Shipping box Shipping skidDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screwsInstalling Optional Mid-Mount Brackets Fastening Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisChassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisAWG stranded copper wire Chassis 4-20 ground screws Telcordia GR-1089 Grounding Hole Pattern and CableInstalling and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply12 Removing Power Supply Vent Plate 13 Installing Power Supply Module 14 Removing Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan TrayFan tray bezel IOM slot Removing a Fan Tray Fan tray slotInstalling and Removing Modules Installing and Removing IOMs18 Installing IOMs 20 Removing IOM Coverplate IOM slot IOM coverplate Captive screws IOM guide railsInstalling and Removing CMs 21 Installing Control ModuleReplacing the CM Battery Installing and Removing FMs 22 Installing Fabric ModuleInstalling an XFP/SFP Module Connecting Fiber-Optic Cables Removing an XFP/SFP ModuleXFP transceiver Port slot Release handle SFP transceiver MT-RJ Connecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 25 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 26 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45Connecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsInstalling the Cable Management Assembly Optional Cable Management Kit32 Installing the Cable Management Assembly Powering Up the Matrix X4-C Chassis LEDs and Reset ButtonFunction LED Activity DC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions AC Power LEDFan Tray LED Fan Tray LED DefinitionsFunction LED Activity Module LEDs and Reset Button Control and Fabric Module LEDsFabric Module Control Module CM & FM LEDs State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM LEDs Only State LED ActivityStatus LED LED Activity First-Time Quick ConfigurationIOM LED Definitions Ethernet Port LED RX/TX LED ActivityEnabling NTP Configuring DhcpAssigning an IP Address to eth0 Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Specification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications AC Power Supply ModuleTable A-2 AC Power Supply Requirements Table A-3 Module Power SpecificationsRedundancy Configurations for AC Line 100-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Table A-5 Redundancy Configurations for AC Line 200-240 VacGigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications 10 µm SMF MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4