Enterasys Networks X009-U manual Setting Up the Matrix X4-C Chassis, Setup Order

Page 35

Setting Up the Matrix X4-C Chassis

Setting Up the Matrix X4-C Chassis

The following sections describe the procedures that must be followed to complete chassis installation. Chassis are shipped with all slots labeled “1” open. Coverplates over IOM slot 1, Fabric and Control Module slot 1, fan tray slots 1 and 2, and PS1 (power supply) are removed, and the slots are ready for module installation.

Setup Order

Once a suitable site has been chosen, proceed to install the Matrix X4‐C chassis in a rack. It is recommended that the Matrix X4‐C chassis installation proceed in this order:

1.Mount the chassis to a 19‐inch (48.26‐centimeter) rack or other secure location. Refer to “Installing the Matrix X4‐C Chassis” on page 3‐5.

2.Perform chassis bonding and grounding. Refer to “Chassis Bonding and Grounding” on page 3‐9.

3.Attach the Electrostatic Discharge wrist strap. Refer to “Attaching the Electrostatic Discharge Wrist Strap” on page 3‐11.

4.Install power supply module(s). Refer to “Installing and Removing a Power Supply” on page 3‐11.

5.Install fan trays. Refer to “Installing a Fan Tray” on page 3‐16.

6.Install IOMs, Fabric Modules, and Control Modules. Refer to “Installing and Removing Modules” on page 3‐18.

7.Attach cabling to the cable management panels. Refer to “Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit” on page 3‐24.

8.Install the optional Cable Management Kit, if purchased, and gather and wrap cables in the velcro cable straps. Refer to “Optional Cable Management Kit” on page 3‐35.

9.Locate and learn the function of IOM, CM, and FM LEDs and the Reset button. Refer to “LEDs and Reset Button” on page 3‐37.

10.Minimally configure the X4‐C chassis to get it up and running and ready for more extensive software configuration. Refer to “First‐Time Quick Configuration” on page 3‐42.

Installing the Matrix X4-C Chassis

The Matrix X4‐C chassis is designed to be mounted in a standard 19‐inch (48.26‐centimeter) equipment rack or cabinet. Use the following guidelines to mount the chassis:

•Allow at least 30.96 centimeters (12.19 inches) of clearance in front of the rack for chassis installation.

•Install the following optional rack supports:

•Rack support brackets are optional but recommended for four‐post cabinet installations.

•Mid‐mount brackets are optional but recommended for two‐post racks (support for shorter racks).

•Attach the Matrix X4‐C chassis ears to the rack.

•Install grounding cables, as necessary.

Matrix X4-C Chassis Installation Guide 3-5

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables For information about Refer to Using This GuideWho Should Use This Guide Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies X4-C Control Module FeaturesX4-C Input/Output Modules Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply Replacement X4-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Installing the Matrix X4-C Chassis Setting Up the Matrix X4-C ChassisSetup Order Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsGrounding Receptacle Plug Wrist strap Installing and Removing a Power SupplyAttaching the Electrostatic Discharge Wrist Strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyFan tray bezel IOM slot Installing and Removing a Fan TrayInstalling a Fan Tray Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiver Connecting Fiber-Optic CablesRemoving an XFP/SFP Module MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 USB device Control Module USB port Installing a Compact Flash CardCompact Flash card Connector Control Module Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisAC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions Function LED Activity DC Power LEDFunction LED Activity Fan Tray LEDFan Tray LED Definitions Fabric Module Control Module Module LEDs and Reset ButtonControl and Fabric Module LEDs CM LEDs Only State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM & FM LEDs State LED ActivityEthernet Port LED RX/TX LED Activity First-Time Quick ConfigurationIOM LED Definitions Status LED LED ActivityNaming the Matrix X4-C Configuring DhcpAssigning an IP Address to eth0 Enabling NTPFirst-Time Quick Configuration Matrix X4-C Chassis Setup AC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications SpecificationTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Redundancy Configurations for AC Line 100-240 VacTable A-9 Recommended Cable Types and Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-8 XFP Fiber-Optic Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical Specifications 10 µm SMFTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceIndex MT-RJ NTP Index-4
Top Page Image Contents