Enterasys Networks X009-U manual Connecting the CM COM Port to a VT Series Terminal

Page 58

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

Figure 3-25 Connecting an IBM PC or Compatible

4

2

31

STATUS

ACTIVE/

STANDBY

RESET

USB

ETHERNET

COM

1UTP cable with RJ45 connectors

2RJ45 COM port

3RJ45-to-DB9 PC adapter

4IBM PC or compatible device

Connecting the CM COM Port to a VT Series Terminal

To connect a VT Series terminal to the CM COM port (Figure 3‐26), use a UTP cable with RJ45 connectors and a user‐supplied RJ45‐to‐DB25 female adapter. Proceed as follows:

1.Connect the RJ45 connector at one end of the cable to the COM port on the CM.

2.Plug the RJ45 connector at the other end of the cable into a user‐supplied RJ45‐to‐DB25 female adapter.

3.Connect the RJ45‐to‐DB25 adapter to the port labeled COM on the VT terminal.

4.Turn on the terminal and access the Setup Directory. Set the following parameters:

Parameter

Setting

 

 

Mode

7 Bit Control

 

 

Transmit

Transmit=19,200

 

 

 

Bits Parity

8

Bits, No Parity

 

 

 

Stop Bit

1

Stop Bit

 

 

 

5.Connect the X4‐C’s power cords. Refer to “Powering Up the Matrix X4‐C Chassis” on page 3‐37.

3-28 Matrix X4-C Chassis Setup

Image 58
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X4-C Chassis with Redundant Power Supplies X4-C Input/Output Modules FeaturesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X4-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X4-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X4-C Chassis Setup Required ToolsUnpacking the Matrix X4-C Chassis Shipping straps Shipping box Shipping skidDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setup Order Setting Up the Matrix X4-C ChassisInstalling the Matrix X4-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screwsInstalling Optional Mid-Mount Brackets Fastening Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisChassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisAWG stranded copper wire Chassis 4-20 ground screws Telcordia GR-1089 Grounding Hole Pattern and CableAttaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply12 Removing Power Supply Vent Plate 13 Installing Power Supply Module 14 Removing Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing a Fan Tray Installing and Removing a Fan TrayFan tray bezel IOM slot Removing a Fan Tray Fan tray slotInstalling and Removing Modules Installing and Removing IOMs18 Installing IOMs 20 Removing IOM Coverplate IOM slot IOM coverplate Captive screws IOM guide railsInstalling and Removing CMs 21 Installing Control ModuleReplacing the CM Battery Installing and Removing FMs 22 Installing Fabric ModuleInstalling an XFP/SFP Module Removing an XFP/SFP Module Connecting Fiber-Optic CablesXFP transceiver Port slot Release handle SFP transceiver MT-RJ Connecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 25 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 26 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsInstalling the Cable Management Assembly Optional Cable Management Kit32 Installing the Cable Management Assembly Powering Up the Matrix X4-C Chassis LEDs and Reset ButtonFunction LED Activity DC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions AC Power LEDFan Tray LED Definitions Fan Tray LEDFunction LED Activity Control and Fabric Module LEDs Module LEDs and Reset ButtonFabric Module Control Module CM & FM LEDs State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM LEDs Only State LED ActivityStatus LED LED Activity First-Time Quick ConfigurationIOM LED Definitions Ethernet Port LED RX/TX LED ActivityEnabling NTP Configuring DhcpAssigning an IP Address to eth0 Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Specification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications AC Power Supply ModuleTable A-2 AC Power Supply Requirements Table A-3 Module Power SpecificationsRedundancy Configurations for AC Line 100-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Table A-5 Redundancy Configurations for AC Line 200-240 VacTable A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications 10 µm SMF MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4