Enterasys Networks X009-U manual First-Time Quick Configuration, IOM LED Definitions

Page 72

First-Time Quick Configuration

Table 3-4 IOM LED Definitions

Status LED	LED Activity

Diagnostics failed, module requires attention, or state before hardware initializes	Red

LED blinks during initialization and diagnostics	Blinking green

Diagnostics passed and software operational	Green

Not powered	Off

Ethernet Port LED (RX/TX)	LED Activity

Link established	Green

Activity over link	Blinking green

No power, link failure, system failure or administratively disabled	Off

The following additional conditions apply:

•After IOM power up, the STATUS LED will remain red until diagnostics begin then will blink green.

First-Time Quick Configuration

This section describes the minimal configuration required to facilitate first‐time communications with the Matrix X4‐C. Consider the following:

•Decide whether you will configure the Matrix X4‐C for switching (bridging) or routing:

•If routing, assign an IP address to interface eth0 for management access. Refer to “Assigning an IP Address to eth0” on page 3‐43.

•If switching, configure the Dynamic Host Configuration Protocol (DHCP) for network IP address assignment. Refer to “Configuring DHCP” on page 3‐43.

Note: Be aware that a statically or DHCP-assigned IP address is accessible from within that subnet by a host directly connected to the interface (via a switch) but if you need to connect to the console from a host on a different subnet, you must configure a static route to that host. Refer to the Matrix X Router Command Line Interface Reference Guide for more information.

•Enable the Network Time Protocol (NTP) to configure proper chassis clocking. Refer to “Enabling NTP” on page 3‐43.

•Designate a name, location, and contact for the Matrix X4‐C. Refer to “Naming the Matrix X4‐C” on page 3‐43.

For more detailed information about configuring the Matrix X4‐C, refer to the Matrix X Router Configuration Guide, which is available online at:

http://www.enterasys.com/support/manuals

3-42 Matrix X4-C Chassis Setup

Image 72

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X4-C Chassis with Redundant Power Supplies Features X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X4-C Fabric Module Monitor ValuesX4-C Redundant Power Supplies Power Supply LEDsAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X4-C Chassis Setup Required ToolsUnpacking the Matrix X4-C Chassis Shipping straps Shipping box Shipping skidDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screwsInstalling Optional Mid-Mount Brackets Fastening Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisChassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisAWG stranded copper wire Chassis 4-20 ground screws Telcordia GR-1089 Grounding Hole Pattern and CableInstalling and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply12 Removing Power Supply Vent Plate 13 Installing Power Supply Module 14 Removing Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan TrayFan tray bezel IOM slot Removing a Fan Tray Fan tray slotInstalling and Removing Modules Installing and Removing IOMs18 Installing IOMs 20 Removing IOM Coverplate IOM slot IOM coverplate Captive screws IOM guide railsInstalling and Removing CMs 21 Installing Control ModuleReplacing the CM Battery Installing and Removing FMs 22 Installing Fabric ModuleInstalling an XFP/SFP Module Connecting Fiber-Optic Cables Removing an XFP/SFP ModuleXFP transceiver Port slot Release handle SFP transceiver MT-RJ Connecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 25 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 26 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45Connecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsInstalling the Cable Management Assembly Optional Cable Management Kit32 Installing the Cable Management Assembly Powering Up the Matrix X4-C Chassis LEDs and Reset ButtonPower Supply LEDs DC/AC Power Supply PS1-PS3 LED DefinitionsFunction LED Activity DC Power LED AC Power LEDFan Tray LED Fan Tray LED DefinitionsFunction LED Activity Module LEDs and Reset Button Control and Fabric Module LEDsFabric Module Control Module IOM LEDs Control and Fabric Module LED DefinitionsCM & FM LEDs State LED Activity CM LEDs Only State LED ActivityFirst-Time Quick Configuration IOM LED DefinitionsStatus LED LED Activity Ethernet Port LED RX/TX LED ActivityConfiguring Dhcp Assigning an IP Address to eth0Enabling NTP Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Chassis, Power Supply, and Fan Tray Specifications Table A-1 Matrix X4-C SpecificationsSpecification AC Power Supply ModuleTable A-2 AC Power Supply Requirements Table A-3 Module Power SpecificationsGigabit Ethernet Transceiver Specifications XFP Module Power SpecificationsRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 VacGigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-17 MGBIC-08 Optical Specifications 10 µm SMF Table A-19 MGBIC-02 SpecificationsPin Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4