Enterasys Networks X009-U manual Connecting to the CM USB Port

Page 61

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

VT Series Port Adapter Wiring and Signal Diagram

RJ45

 

DB25

 

Pin

Conductor

Pin

Signal

4

Red

2

Transmit (TX)

1

Blue

3

Receive (RX)

6

Yellow

5

Clear to Send (CTS)

5

Green

7

Ground (GRD)

2

Orange

20

Data Terminal Ready

 

Pins

 

Pins

1

8

13

1

RJ45 Connector (Female)

25

14

 

 

 

 

DB25

Connector (Female)

Modem Port Adapter Wiring and Signal Diagram

 

 

RJ45

 

DB25

 

Pin

Conductor

Pin

Signal

1

Blue

2

Transmit (TX)

2

Orange

8

Data Carrier Detect (DCD)

4

Red

3

Receive

5

Green

7

Ground (GRD)

6

Yellow

20

Data Terminal Ready (DTR)

8

Gray

22

Ring Indicator

 

Pins

 

Pins

1

8

1

13

RJ45 Connector (Female)

14

25

 

 

 

 

DB25 Connector (Male)

Connecting to the CM USB Port

The X4‐C supports fast and easy configuration downloads using the CM USB port. Using either a USB storage device (as shown in Figure 3‐28) or USB cable to a PC, you can connect to a PC and download configuration files. Simply attach the memory card or a USB cable to the port and access the CM. Refer to the Matrix X Router Configuration Guide for configuration details.

Matrix X4-C Chassis Installation Guide 3-31

Image 61
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies X4-C Input/Output Modules FeaturesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply LEDs X4-C Redundant Power SuppliesAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setup Order Setting Up the Matrix X4-C ChassisInstalling the Matrix X4-C Chassis Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsAttaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan TrayFan tray bezel IOM slot Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Removing an XFP/SFP Module Connecting Fiber-Optic CablesXFP transceiver Port slot Release handle SFP transceiver MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisDC/AC Power Supply PS1-PS3 LED Definitions Power Supply LEDsFunction LED Activity DC Power LED AC Power LEDFan Tray LED Definitions Fan Tray LEDFunction LED Activity Control and Fabric Module LEDs Module LEDs and Reset ButtonFabric Module Control Module Control and Fabric Module LED Definitions IOM LEDsCM & FM LEDs State LED Activity CM LEDs Only State LED ActivityIOM LED Definitions First-Time Quick ConfigurationStatus LED LED Activity Ethernet Port LED RX/TX LED ActivityAssigning an IP Address to eth0 Configuring DhcpEnabling NTP Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Table A-1 Matrix X4-C Specifications Chassis, Power Supply, and Fan Tray SpecificationsSpecification AC Power Supply ModuleTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsModule Power Specifications Gigabit Ethernet Transceiver Specifications XFPRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 VacTable A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-17 MGBIC-08 Optical Specifications 10 µm SMF Table A-19 MGBIC-02 SpecificationsCOM Port Pinout Assignments Pin Signal Name Input/OutputRegulatory Compliance Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4