Enterasys Networks X009-U manual Powering Up the Matrix X4-C Chassis, LEDs and Reset Button

Page 67

Powering Up the Matrix X4-C Chassis

6.Reattach the bar to the cable management assembly by tightening the two (2) captive screws on the bar.

7.If you wish to remove a cable strap, simply unscrew it from the cable management base panel.

Powering Up the Matrix X4-C Chassis

To power up the Matrix X4‐C chassis, proceed as follows:

1.Plug one end of each power cord (included with the power supply) into the AC power inlet on the chassis back panel and tighten the cord lock bracket screw, as shown in Figure 3‐34.

Figure 3-34 Connecting 20 Amp AC Power Cord to the Power Supply

 

AC INLET 3

AC INLET 2

 

AC INLET 1

 

100 - 125V ~ 15A

100 - 125V ~ 15A

 

100 - 125V ~ 15A

 

200 - 240V ~ 8A

200 - 240V ~ 8A

 

200 - 240V ~ 8A

 

 

50/60 Hz

50/60 Hz

 

50/60 Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

1

Power cord

NOTE: Power cords shown are for North America.

2

AC inlet (AC1) with power cord bracket

Each power unit requires a 20 Amp circuit.

2.Plug the other end of each power cord into a dedicated 20 A/110 Vac or 10 A/220 Vac receptacle. If you are using the optional twist lock power cord, plug it in and turn until it locks securely. Refer to Table A‐6 on page A‐3 for more information.

3.Repeat steps 1 and 2 for all power cords.

4.Ensure that the Power LEDs on each power supply are green.

5.Ensure that all fans in the fan tray unit are operating properly when power is received from the power supply modules (fan tray LED will be green). For more information on the power supply LEDs, refer to “Power Supply LEDs” on page 3‐38.

If you experience any problems with this installation, contact Enterasys Networks for assistance. The Matrix X4‐C is now ready to be configured.

LEDs and Reset Button

The following sections describe LED indications for the following:

Power supplies

Fan Trays

IOM, CM, and FMs (with CM Reset button)

Matrix X4-C Chassis Installation Guide 3-37

Image 67
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies X4-C Input/Output Modules FeaturesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply Replacement X4-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setup Order Setting Up the Matrix X4-C ChassisInstalling the Matrix X4-C Chassis Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsAttaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan TrayFan tray bezel IOM slot Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Removing an XFP/SFP Module Connecting Fiber-Optic CablesXFP transceiver Port slot Release handle SFP transceiver MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisAC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions Function LED Activity DC Power LEDFan Tray LED Definitions Fan Tray LEDFunction LED Activity Control and Fabric Module LEDs Module LEDs and Reset ButtonFabric Module Control Module CM LEDs Only State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM & FM LEDs State LED ActivityEthernet Port LED RX/TX LED Activity First-Time Quick ConfigurationIOM LED Definitions Status LED LED ActivityNaming the Matrix X4-C Configuring DhcpAssigning an IP Address to eth0 Enabling NTPFirst-Time Quick Configuration Matrix X4-C Chassis Setup AC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications SpecificationTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Redundancy Configurations for AC Line 100-240 VacTable A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical Specifications 10 µm SMFTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceIndex MT-RJ NTP Index-4