Enterasys Networks X009-U manual Matrix X4-C Chassis Setup, Required Tools

Page 31

3

Matrix X4-C Chassis Setup

This chapter describes the following:

For information about:

Refer to page ...

 

 

Required Tools

3-1

 

 

Unpacking the Matrix X4-C Chassis

3-2

 

 

Setting Up the Matrix X4-C Chassis

3-5

 

 

Installing and Removing a Power Supply

3-11

 

 

Installing and Removing a Fan Tray

3-16

 

 

Installing and Removing Modules

3-18

 

 

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

3-24

 

 

Optional Cable Management Kit

3-35

 

 

Powering Up the Matrix X4-C Chassis

3-37

 

 

LEDs and Reset Button

3-37

 

 

First-Time Quick Configuration

3-42

 

 

Required Tools

Installation equipment needed includes:

• Box cutter

• Phillips screwdriver

• Flat blade screwdriver

Electrical Hazard: Only qualified personnel should install or service this unit.

Riesgo Eléctrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

A box cutter is required to cut the shipping straps. A Phillips screwdriver is needed to install the unit in a standard 19‐inch (48.26‐centimeter) equipment rack and to install the optional Cable Management Kit (refer to “Optional Cable Management Kit” on page 3‐35). A flat blade screwdriver is used to tighten and loosen captive screws. Refer to Chapter 2, Site and Configuration Guidelines, for guidelines that must be followed to install the Matrix X4‐C chassis.

Matrix X4-C Chassis Installation Guide 3-1

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies X4-C Input/Output Modules FeaturesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply Replacement X4-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setup Order Setting Up the Matrix X4-C ChassisInstalling the Matrix X4-C Chassis Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsAttaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan TrayFan tray bezel IOM slot Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Removing an XFP/SFP Module Connecting Fiber-Optic CablesXFP transceiver Port slot Release handle SFP transceiver MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisAC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions Function LED Activity DC Power LEDFan Tray LED Definitions Fan Tray LEDFunction LED Activity Control and Fabric Module LEDs Module LEDs and Reset ButtonFabric Module Control Module CM LEDs Only State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM & FM LEDs State LED ActivityEthernet Port LED RX/TX LED Activity First-Time Quick ConfigurationIOM LED Definitions Status LED LED ActivityNaming the Matrix X4-C Configuring DhcpAssigning an IP Address to eth0 Enabling NTPFirst-Time Quick Configuration Matrix X4-C Chassis Setup AC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications SpecificationTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Redundancy Configurations for AC Line 100-240 VacTable A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical Specifications 10 µm SMFTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceIndex MT-RJ NTP Index-4
Top Page Image Contents