Enterasys Networks X009-U manual Connecting to the CM COM Port, Parameter Setting

Page 57

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

5.After the chassis has been powered up, verify a link exists by checking that the port RX LED is on (flashing amber, blinking green, or solid green). If the RX LED is off, perform the following steps until it is on:

a.Verify the device at the other end of the segment is on and linked to the segment.

b.If there are separate fiber‐optic connections on the other device, check the crossover of the cables. Swap cable connections if necessary.

c.Check that the fiber‐optic connection meets prescribed dB loss and cable specifications.

6.Repeat steps 1 through 3, above, until all connections have been made.

7.To remove the LC or MT‐RJ cable connector, press its release tab and pull it out of the transceiver.

Connecting to the CM COM Port

This section describes how to install a UTP cable with RJ45 connectors and optional adapters to connect the CM COM port to a PC, VT series terminal, or modem to access local management. This section also details adapter pinout assignments.

The following parts may be needed, depending on the connection:

RJ45‐to‐DB9 female adapter (user‐supplied)

UTP cable with RJ45 connectors (user‐supplied)

RJ45‐to‐DB25 female adapter (user‐supplied)

RJ45‐to‐DB25 male adapter (user‐supplied)

Connecting the CM COM Port to an IBM PC or Compatible Device

To connect an IBM PC or compatible device, running the VT terminal emulation, to the CM COM port (Figure 3‐25), proceed as follows:

1.Connect the RJ45 connector at one end of the cable to the communications COM (Console) port on the CM.

2.Plug the RJ45 connector at the other end of the cable into a user‐supplied RJ45‐to‐DB9 adapter.

3.Connect the RJ45‐to‐DB9 adapter to the communications port on the IBM PC.

4.Turn on the PC and configure your VT emulation package with these parameters:

Parameter

Setting

 

 

 

Mode

7

Bit Control

 

 

Transmit

Transmit=19,200

 

 

Bits Parity

8 Bits, No Parity

 

 

 

Stop Bit

1

Stop Bit

 

 

 

5.Connect the X4‐C’s power cords. Refer to “Powering Up the Matrix X4‐C Chassis” on page 3‐37.

Matrix X4-C Chassis Installation Guide 3-27

Image 57
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X4-C Chassis with Redundant Power Supplies Features X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X4-C Fabric ModulePower Supply LEDs X4-C Redundant Power SuppliesAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X4-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X4-C ChassisDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Rack Rack support brackets Bracket screws Installing Optional Rack Support BracketsFastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisRack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable AWG stranded copper wire Chassis 4-20 ground screwsInstalling and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply Planning12 Removing Power Supply Vent Plate 14 Removing Coverplate from Power Supply Slot 13 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling and Removing a Fan Tray Installing a Fan TrayFan tray bezel IOM slot Fan tray slot Removing a Fan TrayInstalling and Removing IOMs Installing and Removing Modules18 Installing IOMs IOM slot IOM coverplate Captive screws IOM guide rails 20 Removing IOM Coverplate21 Installing Control Module Installing and Removing CMsReplacing the CM Battery 22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Connecting Fiber-Optic Cables Removing an XFP/SFP ModuleXFP transceiver Port slot Release handle SFP transceiver MT-RJ Parameter Setting Connecting to the CM COM Port25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsConnecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit Installing the Cable Management Assembly32 Installing the Cable Management Assembly LEDs and Reset Button Powering Up the Matrix X4-C ChassisDC/AC Power Supply PS1-PS3 LED Definitions Power Supply LEDsFunction LED Activity DC Power LED AC Power LEDFan Tray LED Fan Tray LED DefinitionsFunction LED Activity Module LEDs and Reset Button Control and Fabric Module LEDsFabric Module Control Module Control and Fabric Module LED Definitions IOM LEDsCM & FM LEDs State LED Activity CM LEDs Only State LED ActivityIOM LED Definitions First-Time Quick ConfigurationStatus LED LED Activity Ethernet Port LED RX/TX LED ActivityAssigning an IP Address to eth0 Configuring DhcpEnabling NTP Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Table A-1 Matrix X4-C Specifications Chassis, Power Supply, and Fan Tray SpecificationsSpecification AC Power Supply ModuleTable A-3 Module Power Specifications Table A-2 AC Power Supply RequirementsModule Power Specifications Gigabit Ethernet Transceiver Specifications XFPRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 VacGigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-17 MGBIC-08 Optical Specifications 10 µm SMF Table A-19 MGBIC-02 SpecificationsCOM Port Pinout Assignments Pin Signal Name Input/OutputRegulatory Compliance Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4