Enterasys Networks X009-U Installing a Compact Flash Card, USB device Control Module USB port

Page 62

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

Figure 3-28 Attaching a USB Device to the CM

2

1

STATUS

ACTIVE/

STANDBY

RESET

USB

3

1 USB device

2 Control Module

3 USB port

Installing a Compact Flash Card

The Control Module provides an IDE port housing a 1 GB Flash memory card, as shown in Figure 3‐29. If the factory‐installed card fails or you want to install a new Type I Compact Flash card, simply pull the old card from its connector and insert the new card.

Figure 3-29 Installing Flash Card

STATUS

ACTIVE/

STANDBY

RESET

USB

ETHERNET

COM

2

31

1 Compact Flash card

2 Connector

3 Control Module

3-32 Matrix X4-C Chassis Setup

Image 62

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables For information about Refer to Using This GuideWho Should Use This Guide Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X4-C Chassis with Redundant Power Supplies X4-C Control Module FeaturesX4-C Input/Output Modules Installing Redundant CMs into an Active Matrix X Router CM1 X4-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X4-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X4-C Chassis Setup Required ToolsUnpacking the Matrix X4-C Chassis Shipping straps Shipping box Shipping skidDisassembly Steps 3 Unpacking the Matrix X4-C Chassis Installing the Matrix X4-C Chassis Setting Up the Matrix X4-C ChassisSetup Order Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screwsInstalling Optional Mid-Mount Brackets Fastening Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisChassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisAWG stranded copper wire Chassis 4-20 ground screws Telcordia GR-1089 Grounding Hole Pattern and CableGrounding Receptacle Plug Wrist strap Installing and Removing a Power SupplyAttaching the Electrostatic Discharge Wrist Strap Power Supply Planning Installing a Power Supply12 Removing Power Supply Vent Plate 13 Installing Power Supply Module 14 Removing Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Fan tray bezel IOM slot Installing and Removing a Fan TrayInstalling a Fan Tray Removing a Fan Tray Fan tray slotInstalling and Removing Modules Installing and Removing IOMs18 Installing IOMs 20 Removing IOM Coverplate IOM slot IOM coverplate Captive screws IOM guide railsInstalling and Removing CMs 21 Installing Control ModuleReplacing the CM Battery Installing and Removing FMs 22 Installing Fabric ModuleInstalling an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiver Connecting Fiber-Optic CablesRemoving an XFP/SFP Module MT-RJ Connecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 25 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 26 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 USB device Control Module USB port Installing a Compact Flash CardCompact Flash card Connector Control Module Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsInstalling the Cable Management Assembly Optional Cable Management Kit32 Installing the Cable Management Assembly Powering Up the Matrix X4-C Chassis LEDs and Reset ButtonFunction LED Activity DC Power LED Power Supply LEDsDC/AC Power Supply PS1-PS3 LED Definitions AC Power LEDFunction LED Activity Fan Tray LEDFan Tray LED Definitions Fabric Module Control Module Module LEDs and Reset ButtonControl and Fabric Module LEDs CM & FM LEDs State LED Activity IOM LEDsControl and Fabric Module LED Definitions CM LEDs Only State LED ActivityStatus LED LED Activity First-Time Quick ConfigurationIOM LED Definitions Ethernet Port LED RX/TX LED ActivityEnabling NTP Configuring DhcpAssigning an IP Address to eth0 Naming the Matrix X4-CFirst-Time Quick Configuration Matrix X4-C Chassis Setup Specification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications AC Power Supply ModuleTable A-2 AC Power Supply Requirements Table A-3 Module Power SpecificationsRedundancy Configurations for AC Line 100-240 Vac Gigabit Ethernet Transceiver Specifications XFPModule Power Specifications Table A-5 Redundancy Configurations for AC Line 200-240 VacTable A-9 Recommended Cable Types and Specifications Gigabit Ethernet Transceiver Specifications SFPTable A-8 XFP Fiber-Optic Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications 10 µm SMF MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsIndex MT-RJ NTP Index-4