Viking Access Systems H-10 manual Edge Sensor contact sensor Installation, Manual Release

Page 13

IMPORTANT SAFETY INFORMATION

!WARNING! Not Following these instructions may cause severe injury or death.

NOTE: This type on installation dOEs NOT reverse the gate all the way back to its limits when the edge sensor is obstructed. This installation is only to protect against entrapment and to comply with UL325.

Secondary Entrapment Protection

Edge Sensor (contact sensor) Installation

•Edge Sensors or like must be installed to reduce the risk of entrapment.

•Use only Miller Edge 3-sided activation type MGR20 or MGS20 to comply with UL325

•One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on the bottom edge.

1.A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage.

2.A wireless contact sensor such as one that transmits radio frequency (RF) sig- nals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended end-use conditions.

Manual Release

When manual operation is required:

1.Lift the Access Door, located on the front of the cover.

2.Press the Manual Release Switch to the “RELEASE” Position.

The gate can now be moved manually. To resume normal operation, press the switch to the “ENGAGE” position.

VIKING TECHNICAL SUPPORT 1.800.908.0884	1 1

Image 13

Contents Instructions Viking H-10 Slide Gate Operator Vehicular Gate Operator Revision H10NXMN10.E December Description Parts DiagramOperator References Control Board References EMI Board ConnectorTable of Contents Important Safety Instructions Important Safety InformationImportant Installation Instructions Maintenance Glossary UL325 Gate Operator ClassificationsSecondary Entrapment Protection Photo Beam non-contact sensor InstallationWhen manual operation is required Edge Sensor contact sensor InstallationManual Release Manual Reset for the Audible Alarm Audible Alarm Reset Switch InstallationSingle Phase 50 Hz / 60 Hz SpecificationsAlternative Power 24VAC / VDC 60VA or Solar Locate Control ButtonsConcrete Pad Option Gate Operator InstallationPost Mounting Option Operator Positioning Step Tips for proper ground installation Electrical InstallationHigh Voltage Supply Option Solar Supply Option Low Voltage Supply Option1a 1b Limits SetupTo Readjust the Close Limit To Readjust the Open LimitTwo Wire Communication MASTER/SLAVE SetupMS1 MS2 Required ADD-ON Choose option a or B Wireless Communication OptionsTimer Hold Open Timer Initial SettingsObstruction Detection Sensor Auto Open Power Failure Option Control Board SetupLast Open Power Failure Option Fail Safe/SecureODS Obstruction Detection Sensor Obstruction Sensor Primary Entrapment ProtectionViking Heater Viking Lock ModeThis page Left Blank Intentionally Re-Open Photo Beam vehicular Safety Accessory ConnectionsCOM + Check for proper operationOpen-Stop-Close Radio Receiver TypicalOpen Only Open Commands Anti-Tailgate, Open Commands & Guard StationGuard Station ATG Anti-TailgateViking Loop Rack Guidelines for Loop Installation Accessory ConnectionsMagnetic Lock, Lock Solenoid Power for the LocksMagnetic Lock Lock Solenoid Barrier Arm B-12 Synchronization Option Synchronization with B-12LED References TroubleshootingTroubleshooting LCD Display References LCD MSG MeaningTroubleshooting Error Messages Check SolutionsPower Connections Access Control ConnectionsRelays In General Appendix aGeneral Technical TIP Viking usesCommon Radio Receivers Connections Solar Applications Appendix CPanels Batteries & FuseViking Expansion Products Viking Konnect Diagnostic Tool On-site remoteViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features