Viking Access Systems H-10 manual Troubleshooting, LED References

Page 38

TROUBLESHOOTING

LED References

In addition to the LCD Display, the control board LEDs monitor the various circuits of the control board. Use the table below to identify the corresponding “TS Ref#” and refer to page 38-41 for further troubleshooting.

 

 

 

 

Page 41

#

LED

Status

Meaning

TS Ref#(s)

1

“Magnetic

OFF

At Closed Limit and Magnetic Lock Relay state is closed across “COM” &

 

 

Lock Relay”

 

“N.C”. (pg 34). Gate should be at the Close Limit.

 

 

 

SOLID

Not at Closed Limit and Magnetic Lock Relay state is closed across “COM” &

 

 

 

 

“N.O”. (pg 34). Gate should not be at the Close Limit

 

2

“Check Motor”

OFF

Normal Condition.

 

 

SOLID

The control board is sending power to the motor but the circuit is open.

3

“Battery Low”

OFF

Normal Condition.

 

 

SOLID

Batteries are low. Check power supply to the operator. (pgs 18-19).

 

 

FLASHING

Batteries critically low. Check power supply to the operator. (pgs 18-19).

4

“POWER”

SOLID

Normal Condition.

 

 

FLASHING

Operator is running on batteries only (pgs 18-19).

 

 

OFF

No power to control board.

5

“Radio”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the

 

 

 

Radio terminal (pgs 30, 42).

6

“UL”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the UL

 

 

 

terminal (pgs 12-13, 42).

7

“Re-Open”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the Re-

 

 

 

Open terminal (pgs 29, 32, 42).

8

“ATG”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the ATG

 

 

 

terminal (pgs 31, 42).

7, 8

1, 2 1, 2

1, 2

1, 2, 4, 5

9, 10

9, 10

9, 10

9, 10

3 6

VIKING TECHNICAL SUPPORT 1.800.908.0884

 

 

Image 38
Contents Instructions Viking H-10 Slide Gate Operator Vehicular Gate Operator Revision H10NXMN10.E December Parts Diagram DescriptionOperator References EMI Board Connector Control Board ReferencesTable of Contents Important Safety Information Important Safety InstructionsImportant Installation Instructions Maintenance UL325 Gate Operator Classifications GlossaryPhoto Beam non-contact sensor Installation Secondary Entrapment ProtectionManual Release Edge Sensor contact sensor InstallationWhen manual operation is required Audible Alarm Reset Switch Installation Manual Reset for the Audible AlarmAlternative Power 24VAC / VDC 60VA or Solar SpecificationsSingle Phase 50 Hz / 60 Hz Locate Control ButtonsGate Operator Installation Concrete Pad OptionPost Mounting Option Operator Positioning Step High Voltage Supply Option Electrical InstallationTips for proper ground installation Low Voltage Supply Option Solar Supply OptionLimits Setup 1a 1bTo Readjust the Open Limit To Readjust the Close LimitMS1 MS2 MASTER/SLAVE SetupTwo Wire Communication Wireless Communication Options Required ADD-ON Choose option a or BObstruction Detection Sensor Initial SettingsTimer Hold Open Timer Last Open Power Failure Option Control Board SetupAuto Open Power Failure Option Fail Safe/SecureObstruction Sensor Primary Entrapment Protection ODS Obstruction Detection SensorViking Lock Mode Viking HeaterThis page Left Blank Intentionally COM + Accessory ConnectionsRe-Open Photo Beam vehicular Safety Check for proper operationOpen Only Radio Receiver TypicalOpen-Stop-Close Guard Station Anti-Tailgate, Open Commands & Guard StationOpen Commands ATG Anti-TailgateViking Loop Rack Accessory Connections Guidelines for Loop InstallationMagnetic Lock Lock Solenoid Power for the LocksMagnetic Lock, Lock Solenoid Synchronization with B-12 Barrier Arm B-12 Synchronization OptionTroubleshooting LED ReferencesTroubleshooting LCD MSG Meaning LCD Display ReferencesTroubleshooting Error Messages Solutions CheckAccess Control Connections Power ConnectionsGeneral Appendix aRelays In General Technical TIP Viking usesCommon Radio Receivers Connections Panels Appendix CSolar Applications Batteries & FuseViking Konnect Master/Slave Kit Secure and reliable Viking Konnect Diagnostic Tool On-site remoteViking Expansion Products OUR Continuous Commitment to Excellence Standard Features