Viking Access Systems H-10 manual Troubleshooting

Page 41

	TROUBLESHOOTING
LCD Display References
LCD MSG Meaning	Page 41
LCD MSG Meaning	TS Ref #s

Multi Meter Displays

MOT AMP __._ A

MOT VOLT __._ VDC

AC VOLT __._ VAC

CHARGE __._ VDC

BAT VOLT __._ VDC

This is the motor current amperage during operation

This is the actual motor voltage during operation

This is the actual low voltage AC to the Control Board from the transformer

Indicates the charging voltage to the batteries, if the Battery Switch is in the OFF position.

Indicates battery voltage, if the AC power is discontinued to the Control Board.

EPS2

___% ERR

SPEED __%

OVERLAP _._ SEC

ODS SENS

___%

TIMER __ SEC

HEATER __ OFF

HEATER __ ON

LOCK MOD OFF

LOCK MOD ON

Board Settings Messages

Indicates that the Electronic Positioning Sensor (EPS) needs to be tuned. Error rate is displayed as a percentage

Shows the percentage of speed set by the Speed adjustment on the control board. (pg. 24)

Shows the number of seconds set by the Overlap Adjustment on the con- trol board. This feature is not available on slide gate operator models

Shows the force setting selected to trip the obstruction sensor. (pg. 26)

Shows the amount time set or remaining to hold the gate at the Open Limit position, before the gate starts to close. (pg. 24)

The Integrated Heater is disabled for the open “OPN” and/or close “CLS” limits (pg. 27)

The Integrated Heater has been enabled to turn on at the open “OPN” and/ or close “CLS” limits (pg. 27) “*” will be displayed while it is heating

The Lock Mode feature is turned OFF (pg. 27)

The Lock Mode feature is turned ON (pg. 27)

VIKING TECHNICAL SUPPORT 1.800.908.0884	3 9

Image 41

Contents Instructions Viking H-10 Slide Gate Operator Vehicular Gate Operator Revision H10NXMN10.E December Description Parts DiagramOperator References Control Board References EMI Board ConnectorTable of Contents Important Safety Instructions Important Safety InformationImportant Installation Instructions Maintenance Glossary UL325 Gate Operator ClassificationsSecondary Entrapment Protection Photo Beam non-contact sensor InstallationManual Release Edge Sensor contact sensor InstallationWhen manual operation is required Manual Reset for the Audible Alarm Audible Alarm Reset Switch InstallationSingle Phase 50 Hz / 60 Hz SpecificationsAlternative Power 24VAC / VDC 60VA or Solar Locate Control ButtonsConcrete Pad Option Gate Operator InstallationPost Mounting Option Operator Positioning Step High Voltage Supply Option Electrical InstallationTips for proper ground installation Solar Supply Option Low Voltage Supply Option1a 1b Limits SetupTo Readjust the Close Limit To Readjust the Open LimitMS1 MS2 MASTER/SLAVE SetupTwo Wire Communication Required ADD-ON Choose option a or B Wireless Communication OptionsObstruction Detection Sensor Initial SettingsTimer Hold Open Timer Auto Open Power Failure Option Control Board SetupLast Open Power Failure Option Fail Safe/SecureODS Obstruction Detection Sensor Obstruction Sensor Primary Entrapment ProtectionViking Heater Viking Lock ModeThis page Left Blank Intentionally Re-Open Photo Beam vehicular Safety Accessory ConnectionsCOM + Check for proper operationOpen Only Radio Receiver TypicalOpen-Stop-Close Open Commands Anti-Tailgate, Open Commands & Guard StationGuard Station ATG Anti-TailgateViking Loop Rack Guidelines for Loop Installation Accessory ConnectionsMagnetic Lock Lock Solenoid Power for the LocksMagnetic Lock, Lock Solenoid Barrier Arm B-12 Synchronization Option Synchronization with B-12 LED References TroubleshootingTroubleshooting LCD Display References LCD MSG MeaningTroubleshooting Error Messages Check SolutionsPower Connections Access Control ConnectionsRelays In General Appendix aGeneral Technical TIP Viking usesCommon Radio Receivers Connections Solar Applications Appendix CPanels Batteries & FuseViking Konnect Master/Slave Kit Secure and reliable Viking Konnect Diagnostic Tool On-site remoteViking Expansion Products OUR Continuous Commitment to Excellence Standard Features