Bosch Appliances MIC412 MIC 412TI and MIC 412TF Power Supply Units, PCB Earth Link

Page 15

MIC412TI and MIC412TF Camera Installation and Operation Manual

CHAPTER 3 Power Supply Installation

Note: Refer to the MIC Series Power Supplies Installaion Manual for detailed power supply information.

MIC 412TI and MIC 412TF Power Supply Units

MIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL

The power supply provides power for a single MIC412 camera unit from either a 24 VAC source (MIC-24PSU-UL), 240 VAC source (MIC-240PSU-UL) or a 115 VAC source (MIC-115PSU-UL).

In addition the unit provides all the terminations required to connect a MIC 412 camera to third party equipment.

A second independent 12 V (600 mA) power supply is also included to drive any internally fitted optional interface cards.

Dimensions (W x H x L):

Power supply enclosure: 240 x 90.5 x 160 mm (9.5 x 3.6 x 6.3 in.)

WARNING: All external wires for installation applications must be routed through a permanently earthed metal conduit.

The Power Supply Unit provides all the support functions for connecting the camera to third party equipment. It comprises of:

EN 15

1.A weather-resistant (IP65) cast-aluminium box pre-fitted with three (3) cable glands.

2.A power supply for the MIC 412 camera.

3.Provision for driving various interface cards mounted internally to the power supply box, for example an alarm interface card (non-IR power supplies only).

4.Provision for a signal interface card (BP-3 or BP-4) to connect telemetry to Bosch Biphase equipment.

5.Screw termination of all composite, telemetry and ancillary cables in the box.

6.Earth isolation and termination within the unit to correctly control video earthing and to prevent earth loop.

PCB Earth Link

The PCB has one link option next to HD1 to allow the power supply to be set up for different earthing schemes: The Earth Link should be broken if there is a separate connection between video screen and earth. This usually occurs on copper connected systems where all the copper video coaxes are taken back to the control room to be connected to a central earth point. If fibre optics or other indirect connections are used to get data and video to and from the control room then the earth link should be left intact provided it is the only camera end earth reference point.

Power Supply Layout and Connections

The power supply PCB has the following connections as shown on Figure A:-

HD1 – Power Input Connector (screw terminal) HD2 - Tamper Switch header (screw terminal)

HD3 - Composite cable header (Connections to camera head, screw terminal) HD4 - Telemetry header (molex connection)

HD5 - Telemetry header (screw terminal) HD6 - Washer pump header (screw terminal)

HD8 - Keyboard power connector (demo purposes only, not normally fitted) CN1 - Video out connection header (BNC)

CN2 - Add on card header (plug in)

Figure A and the following tables show the connections required.

Bosch Security Systems

Issue 8

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Appendices Glossary of TermsIntroduction MIC412 Camera Versions MIC 412 Power Supply Unit Versions and OptionsWiper FeaturesPackaging Contents MIC 412 OptionsInstallation Environment Bosch Security Systems Issue Key to MIC-PMB drawing Associated Equipment and Typical InstallationsInstallation Instructions Hardware InstallationEarthing of the MIC 412 camera Lightning ProtectionElectrical Connections PCB Earth Link MIC 412TI and MIC 412TF Power Supply UnitsPower Supply Layout and Connections MIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-ULTable D -Telemetry Connections to HD3, HD4 and HD5 HD3Rating for 115v Primary Terminal Box ConnectorTerminal Box ID Marking Fuse Fuse function Rating for 240v PrimaryCommissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor Connecting the MIC 412 to the PCConnecting the Greenwich Adaptor Table G Connecting the Greenwich AdaptorTable I Camera Interface Control Settings DIP Switch Connecting the MIC-USB485CVTR, USB to RS485 ConverterCamset Tabs Wire RS485 Wire RS422 HD4 or HD5 MIC-USB485CVTR and Universal Camset Software InstallationStandard Controls Boot MessagesMIC Settings Commissioning the MIC412 through Universal CamsetCamset Settings Manual Control Pan, Tilt and Zoom Controls Auxiliaries Preset PositionsIris Controls Focus ControlsPreset Tours Tour ControlsPattern Tours Clear MIC SetupsSoft Stops and Non Dwell Zones Non-Dwell ZoneGeneral Settings Other controls Auto Home ControlsDefault Settings Relay State, Activation and Re-arm Multi Alarm SettingsLearn Alarm Positions Frame Integration SettingsPrivacy Controls Privacy and CaptionsPrivacy Calibration Captions Gain and Auto Gain Modes FFC Mode and SettingsThermal Shutter Open/CloseClear All Statistics Advanced SettingsTemperature and Humidity TimersUpload Eeprom From File Eeprom CopierOnly Download Eeprom To FileMatrix Controls Manual and Preset / Goto ControlsPOT Test Menu Controls Panasonic OnlyVisible Traces Pot Test ControlsComms Pot Test ResultsMouse Point Values Send Direct Command Cam Comms Communications TestingAlarms MIC CommsSonySet Controls Get Preset from MICSend Preset to MIC Sony SetClear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to FileTable K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Learning a preset Help MIC412 Preset Codes for the Thermal ImagerBosch Protocol Aux Number Aux On Function Aux Off Function Go to a preset36x optical zoom module MIC412TI and TF Dual Optical/Thermal PTZ CameraConnectivity Appendix a Sonyset Camera Commands Dimension DrawingsMIC 412 models Upright 90 Dimension Drawings Pelco Appendix B Protocol Preset CodesWashwipeonpreset Washwipeoffpreset Vision Special Setup PresetsAmerican Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-PacificBosch Security Systems, Inc
Top Page Image Contents