Bosch Appliances MIC412 Advanced Settings, Temperature and Humidity, Timers, Clear All Statistics

Page 37

MIC412TI and MIC412TF Camera Installation and Operation Manual

Advanced Settings

The Advanced Settings tab offers engineering and special auxiliary control modes for Pelco and Panasonic protocols (see Help file for details).

The MIC stores various statistics about itself, including temperature and humidity, and various timers for different parameters, which may be of interest to the end user, but are mainly implemented as an engineering tool.

EN 37

Temperature and Humidity

This will only work if the MIC400 has the appropriate control card with the temperature and humidity sensor attached. Current, Max and Min are displayed for both in degrees and a percentage respectively. If the MIC reaches 70% humidity inside the head a small "H" is displayed in the top left corner indicating a Humidity problem. If this appears, make contact with Bosch Security Systems.

Timers

The timers monitor most of the common functionalities of a MIC: Panning, Tilting, On Tour, Since Built, Stationary, Wiping and IR Lamp shown in Weeks, Days, Hours, Minutes and Seconds.

Clear All Statistics

This function will set Max and Min for temperature and humidity to the current reading, and will clear all of the timers to "0". This feature should only be used when a MIC is first built or repaired, and therefore is locked out with the Advanced Controls Password.

MIC Serial Number

This feature is used to set or read the actual MIC Serial Number. This may be required to reprogram the MIC through the telemetry. The Set function is locked out with the Advanced Password as this should only be performed at the manufacturing stage, however read is available to use as required.

Bosch Security Systems

Issue 8

Image 37

Contents MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Appendices Glossary of TermsIntroduction MIC412 Camera Versions MIC 412 Power Supply Unit Versions and OptionsPackaging Contents FeaturesMIC 412 Options WiperInstallation Environment Bosch Security Systems Issue Key to MIC-PMB drawing Associated Equipment and Typical InstallationsInstallation Instructions Hardware InstallationLightning Protection Earthing of the MIC 412 cameraElectrical Connections Power Supply Layout and Connections MIC 412TI and MIC 412TF Power Supply UnitsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth LinkTable D -Telemetry Connections to HD3, HD4 and HD5 HD3Terminal Box ID Marking Fuse Fuse function Terminal Box ConnectorRating for 240v Primary Rating for 115v PrimaryCommissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the Greenwich Adaptor Connecting the MIC 412 to the PCTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorConnecting the MIC-USB485CVTR, USB to RS485 Converter Table I Camera Interface Control Settings DIP SwitchCamset Tabs Wire RS485 Wire RS422 HD4 or HD5 MIC-USB485CVTR and Universal Camset Software InstallationMIC Settings Boot MessagesCommissioning the MIC412 through Universal Camset Standard ControlsCamset Settings Manual Control Pan, Tilt and Zoom Controls Iris Controls Preset PositionsFocus Controls AuxiliariesTour Controls Preset ToursPattern Tours Soft Stops and Non Dwell Zones MIC SetupsNon-Dwell Zone ClearGeneral Settings Other controls Auto Home ControlsDefault Settings Learn Alarm Positions Multi Alarm SettingsFrame Integration Settings Relay State, Activation and Re-armPrivacy Controls Privacy and CaptionsPrivacy Calibration Captions Thermal FFC Mode and SettingsShutter Open/Close Gain and Auto Gain ModesTemperature and Humidity Advanced SettingsTimers Clear All StatisticsOnly Eeprom CopierDownload Eeprom To File Upload Eeprom From FilePOT Test Manual and Preset / Goto ControlsMenu Controls Panasonic Only Matrix ControlsVisible Traces Pot Test ControlsPot Test Results CommsMouse Point Values Send Direct Command Alarms Communications TestingMIC Comms Cam CommsSend Preset to MIC Get Preset from MICSony Set SonySet ControlsLoad Table from File to MIC Execute this PresetSave Table from MIC to File Clear TableTable K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Learning a preset Help MIC412 Preset Codes for the Thermal ImagerBosch Protocol Aux Number Aux On Function Aux Off Function Go to a preset36x optical zoom module MIC412TI and TF Dual Optical/Thermal PTZ CameraConnectivity Dimension Drawings Appendix a Sonyset Camera CommandsMIC 412 models Upright 90 Dimension Drawings Pelco Appendix B Protocol Preset CodesWashwipeonpreset Washwipeoffpreset Vision Special Setup PresetsAmerican Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Europe, Middle East, Africa Contact AmericasAsia-Pacific Bosch Security Systems IncBosch Security Systems, Inc