Bosch Appliances MIC412 operation manual Pot Test Controls, Visible Traces

Page 40

MIC412TI and MIC412TF Camera Installation and Operation Manual

command is sent. The numeric key pad controls also work whilst in pot test although the learn preset method using the number keys does not.

Pot Test Controls

Start

This initiates the Pot Test process. Continual commands will be sent requesting the MIC’s current data, the responses will be decoded and data printed and plotted on the display.

Stop

This stops the process running. Pot Test is also stopped when another tab is selected to ensure communications aren't held up when trying to perform an operation from another page.

Clear Trace

This will clear the graph plotted and reset the cursor to the left hand side of the picture box.

Reset Measurements

Whilst Pot Test monitors the current values, it also measures the maximum, minimum and average readings for PWM in both the pan and tilt axis. These are displayed below the current readings in Pan Readings and Tilt Readings respectively. This button enables the user to reset these calculated values.

Save Plot

This control enables the graph plot to be saved as a .jpg image to a location determined on the save dialog box that opens.

EN 40

Rotation Analyzer

This sub window can be used to accurately measure the PWM of either axis of the MIC, plotting the data against position rather than reading, which provides a easy to read way of locating tight or loose spots in the tested axis. The results can then be saved as a Word .doc report and automatically printed to the default printer, whilst also giving the option to simply view the results on the window. The user can then use the mouse on the plot to drive the MIC back to suspect positions for further analysis. This functionality is only available in FV protocol, and works best with a baud rate of 9600. To exit the sub window press Close.

Visible Traces

This section enables the switching on and off of the various traces available from the Pot Test plot. By default current Pan and Tilt position and PWM is displayed, and the following can be added, which are all real time calculations made since Reset Measurements was last pressed:

•Min Pan PWM - Maroon

•Max Pan PWM - Red

•Average Pan PWM - Orange

•Min Tilt PWM - Maroon

•Max Tilt PWM - Red

•Average Tilt PWM - Orange

As these are displayed in the same colors, it is recommended that only one set of Max, Min, Average be displayed at any one time.

Bosch Security Systems

Issue 8

Page 39 Page 41
Image 40
Page 39 Page 41
Contents MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Terms Glossary of AppendicesIntroduction MIC 412 Power Supply Unit Versions and Options MIC412 Camera VersionsFeatures Packaging ContentsMIC 412 Options WiperInstallation Environment Bosch Security Systems Issue Associated Equipment and Typical Installations Key to MIC-PMB drawingHardware Installation Installation InstructionsLightning Protection Earthing of the MIC 412 cameraElectrical Connections MIC 412TI and MIC 412TF Power Supply Units Power Supply Layout and ConnectionsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth LinkHD3 Table D -Telemetry Connections to HD3, HD4 and HD5Terminal Box Connector Terminal Box ID Marking Fuse Fuse functionRating for 240v Primary Rating for 115v PrimaryCommissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the MIC 412 to the PC Connecting the Greenwich AdaptorTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorConnecting the MIC-USB485CVTR, USB to RS485 Converter Table I Camera Interface Control Settings DIP SwitchCamset Tabs Wire RS485 Wire RS422 MIC-USB485CVTR and Universal Camset Software Installation HD4 or HD5Boot Messages MIC SettingsCommissioning the MIC412 through Universal Camset Standard ControlsCamset Settings Manual Control Pan, Tilt and Zoom Controls Preset Positions Iris ControlsFocus Controls AuxiliariesTour Controls Preset ToursPattern Tours MIC Setups Soft Stops and Non Dwell ZonesNon-Dwell Zone ClearGeneral Settings Auto Home Controls Other controlsDefault Settings Multi Alarm Settings Learn Alarm PositionsFrame Integration Settings Relay State, Activation and Re-armPrivacy and Captions Privacy ControlsPrivacy Calibration Captions FFC Mode and Settings ThermalShutter Open/Close Gain and Auto Gain ModesAdvanced Settings Temperature and HumidityTimers Clear All StatisticsEeprom Copier OnlyDownload Eeprom To File Upload Eeprom From FileManual and Preset / Goto Controls POT TestMenu Controls Panasonic Only Matrix ControlsPot Test Controls Visible TracesPot Test Results CommsMouse Point Values Send Direct Command Communications Testing AlarmsMIC Comms Cam CommsGet Preset from MIC Send Preset to MICSony Set SonySet ControlsExecute this Preset Load Table from File to MICSave Table from MIC to File Clear TableTable K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Help MIC412 Preset Codes for the Thermal Imager Learning a presetGo to a preset Bosch Protocol Aux Number Aux On Function Aux Off FunctionMIC412TI and TF Dual Optical/Thermal PTZ Camera 36x optical zoom moduleConnectivity Dimension Drawings Appendix a Sonyset Camera CommandsMIC 412 models Upright 90 Dimension Drawings Appendix B Protocol Preset Codes PelcoWashwipeonpreset Washwipeoffpreset Special Setup Presets VisionAmerican Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Contact Americas Europe, Middle East, AfricaAsia-Pacific Bosch Security Systems IncBosch Security Systems, Inc
Top Page Image Contents