Bosch Appliances MIC412 operation manual Manual Control Pan, Tilt and Zoom Controls

Page 25

MIC412TI and MIC412TF Camera Installation and Operation Manual

EN 25

MIC Model

This provides a list of all the available MIC Models. This should be set to the type of camera being controlled as Camset is then set up accordingly to provide more or less options dependant upon the combination of this setting with the Camset Protocol above.

Comm Port

This provides a list of the available Comm Ports detected by the software on the PC. If a comm port is in use when it is selected the user will be prompted with an error, and should either select another port or close the application currently using it.

If the MIC-USB485CTR, USB to RS485 convertor is being used, when plugged in this will show on the Comm Port drop down menu as USB, simply select to use.

The final option is close which will close any open communications port meaning that other applications can then use the port for other purposes.

Camset Baud Rate

This displays the current Baud Rate at which outgoing messages are sent, and the other options available for the given protocol above. Changing this without first changing the MIC baud rate will cause a loss of communications.

RTS

This defines the state of the RTS line on the serial port which can be used power in line RS232 to 485 adapters.

Comms Mode

There are 3 available options for comms modes:

Full Duplex: Full 2 way 4 wire communications connection. Messages are transmitted and received on separate comms pairs.

Half Duplex: 2 way, 2 wire communications connection. Messages are transmitted and received on the same pair of wires. The 485 drivers deal with the switching of the line directions automatically.

Simplex: 1 way 2 wire communications connection. Messages are only transmitted

to the camera. This will work for most manual controls, but anything that requires a response, such as Pot Test, Exact Positioning, and Programming etc will fail.

Reset Camset

This re-initializes all of the controls for the software to the state it would be on boot.

Manual Control

Pan, Tilt and Zoom Controls

The Up, Down, Left and Right buttons send commands to the MIC to move in the selected direction at the speed indicated by the Speed Slider.

Bosch Security Systems

Issue 8

Image 25

Contents MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Appendices Glossary of TermsIntroduction MIC412 Camera Versions MIC 412 Power Supply Unit Versions and OptionsPackaging Contents FeaturesMIC 412 Options WiperInstallation Environment Bosch Security Systems Issue Key to MIC-PMB drawing Associated Equipment and Typical InstallationsInstallation Instructions Hardware InstallationLightning Protection Earthing of the MIC 412 cameraElectrical Connections Power Supply Layout and Connections MIC 412TI and MIC 412TF Power Supply UnitsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth LinkTable D -Telemetry Connections to HD3, HD4 and HD5 HD3Terminal Box ID Marking Fuse Fuse function Terminal Box ConnectorRating for 240v Primary Rating for 115v PrimaryCommissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the Greenwich Adaptor Connecting the MIC 412 to the PCTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorConnecting the MIC-USB485CVTR, USB to RS485 Converter Table I Camera Interface Control Settings DIP SwitchCamset Tabs Wire RS485 Wire RS422 HD4 or HD5 MIC-USB485CVTR and Universal Camset Software InstallationMIC Settings Boot MessagesCommissioning the MIC412 through Universal Camset Standard ControlsCamset Settings Manual Control Pan, Tilt and Zoom Controls Iris Controls Preset PositionsFocus Controls AuxiliariesTour Controls Preset ToursPattern Tours Soft Stops and Non Dwell Zones MIC SetupsNon-Dwell Zone ClearGeneral Settings Other controls Auto Home ControlsDefault Settings Learn Alarm Positions Multi Alarm SettingsFrame Integration Settings Relay State, Activation and Re-armPrivacy Controls Privacy and CaptionsPrivacy Calibration Captions Thermal FFC Mode and SettingsShutter Open/Close Gain and Auto Gain ModesTemperature and Humidity Advanced SettingsTimers Clear All StatisticsOnly Eeprom CopierDownload Eeprom To File Upload Eeprom From FilePOT Test Manual and Preset / Goto ControlsMenu Controls Panasonic Only Matrix ControlsVisible Traces Pot Test ControlsPot Test Results CommsMouse Point Values Send Direct Command Alarms Communications TestingMIC Comms Cam CommsSend Preset to MIC Get Preset from MICSony Set SonySet ControlsLoad Table from File to MIC Execute this PresetSave Table from MIC to File Clear TableTable K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Learning a preset Help MIC412 Preset Codes for the Thermal ImagerBosch Protocol Aux Number Aux On Function Aux Off Function Go to a preset36x optical zoom module MIC412TI and TF Dual Optical/Thermal PTZ CameraConnectivity Dimension Drawings Appendix a Sonyset Camera CommandsMIC 412 models Upright 90 Dimension Drawings Pelco Appendix B Protocol Preset CodesWashwipeonpreset Washwipeoffpreset Vision Special Setup PresetsAmerican Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Europe, Middle East, Africa Contact AmericasAsia-Pacific Bosch Security Systems IncBosch Security Systems, Inc