Panasonic WV-SW458E, WV-SW458ME Ratings Terminal name, Alarm OUT, AUX OUT

Page 26
• Supply voltage:
• Recommended sensitivity of microphone:
Recommended microphone:

z Connect the microphone/line input cable and the microphone (for use of the audio reception

function).

 

Input impedance:

2 kΩ±10 %

Recommended cable length: Less than 1 m {3.3 feet} (for microphone input) Less than 10 m {33 feet} (for line input) Plug-in power type microphone (option) Connect a monaural mini plug (ø3.5 mm).

2.5 V ±0.5 V

−48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)

IMPORTANT:

Connect/disconnect the external speaker cables or audio/video cables after turning off the power of the camera and the amplifier. Otherwise, loud noise may come out from the speaker.

xConnect an external amplifier-embedded speaker to the audio output cable (for use of the audio transmission function).

Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.).

Recommended cable length: 10 m {33 feet} or less

c Connect the alarm input/output cable.

<Ratings>

Terminal name

Ratings

 

 

 

ALARM OUT, AUX OUT

Open collector output (maximum applied voltage: 20 V DC)

 

 

 

 

Open

4 V DC - 5 V DC by internal pull-up

 

 

 

 

Close

Output voltage 1 V DC or less (50 mA or less)

 

 

ALARM IN

Non-voltage make contact input (4 V DC - 5 V DC, internally pulled

 

 

up)

 

 

 

 

Off

Open or 4 V DC - 5 V DC

 

 

 

 

On

Make contact with GND (required drive current: 1 mA or more)

 

 

 

Note:

Check if rating of an external device such as a sensor is applicable to the rating of this product by referring to the provided operating instructions.

Speci￿cation of 4P alarm cable (accessory)

GND (black)

ALARM IN3, AUX OUT (gray) (Terminal 3)

ALARM IN2, ALARM OUT (red) (Terminal 2)

ALARM IN1 (green) (Terminal 1)

26

Image 26
Contents Model No. WV-SW458/WV-SW458M WV-SW458E/WV-SW458ME WV-SW458E, WV-SW458ME Contents Important safety instructions Disclaimer of warranty Limitation of liabilityMain functions PrefaceAbout notations System requirements for a PC CPUTrademarks and registered trademarks CopyrightNetwork security Precautions Precautions for use This product has no power switch Do not damage the power cableTurn the power off when cleaning this product Cleaning this product bodyDiscoloration on the color filter of the MOS image sensor Mount bracket accessory SW458Code label Indication labelDo not place this product in the following places Precautions for installationInstalling place About the network connectionRadio disturbance Time & date settingProcure fixing screws separately RouterMajor operating controls About the indicators inside the SD memory card slot cover About the Initial SET buttonPreparations Using the side cable access hole SW458M Mounting hole patternInstalling the camera directly on the ceiling or wall SW458M Using the mount bracket accessory SW458 Ø1-1/16 inches Cable access hole For use of the hole Camera attachment accessory Fixing screws accessory Insert/remove an SD memory card WV-SW458 Power cableConnection WV-SW458MRatings Terminal name Alarm OUT, AUX OUTAlarm When using 12 V DC power supply*1 When using PoE IEEE802.3af compliantHow to wind the supplied waterproof tape LAN cableRequired cable Installation Using a two-gang junction boxUsing the mount bracket SW458 Page Use the bit for tamperproof screw accessory Configure the network settings Configuring the camera so that it can be accessed from a PCPage Troubleshooting When using DC power supplyAlarm in 1, Alarm in 2/ Alarm OUT SpecificationsLimited Power Source BasicViqs ELCATW1/ ATW2/ AWC Jpeg LensNetwork Jpeg Mjpeg IGMP, ICMP, ARPStandard accessories Optional accessoriesPage Page PGQX1203YA For business users in the European UnionFor U.S. and Canada