Panasonic WV-SW458ME When using 12 V DC power supply*1, When using PoE IEEE802.3af compliant

Page 27

IMPORTANT:

Input and output of the External I/O terminal 2 and 3 can be switched by configuring the setting. “Off” is selected by default. It is possible to determine whether or not to receive input from External I/O terminal 2 and 3 (ALARM IN2, 3) by selecting “Off”, “Alarm input”, “Alarm output” or “AUX output” for “Terminal 2” or “Terminal 3” on the [Alarm] tab of the “Alarm” page. Refer to the Operating Instructions on the provided CD-ROM for further information.

When using the External I/O terminals as the output terminals, ensure they do not cause signal collision with external signals.

In order for the External I/O terminal to detect alarm inputs when the terminal status is changed from Open to Close (On) or from Close to Open (Off), about 100 ms or more is needed. Because alarms cannot be detected for about 5 seconds after a detection is made, alarm inputs received within about 5 seconds after an alarm is detected are not detected.

vConnect a LAN cable (category 5 or better, straight, STP*) to the network connector.

*E model only

b Connect the power cable.

IMPORTANT:

• The 12 V DC power supply shall be insulated from the commercial AC power.

When using 12 V DC power supply*1

Connect the output cable of the AC adaptor to the 2P power cable (accessory).

When using PoE (IEEE802.3af compliant)

Connect a LAN cable (category 5 or better, straight, STP*2) between a PoE device (such as a hub) and the network connector of the camera.

*1 ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY or LIMITED POWER SOURCE. *2 E model only

IMPORTANT:

Use all 4 pairs (8 pins) of the LAN cable.

The maximum cable length is 100 m {328 feet}.

Make sure that the PoE device in use is compliant with IEEE802.3af standard.

When connecting both the 12 V DC power supply and the PoE device for power supply,

12 V DC will be used for power supply. Depending on the PoE device used, the power supply lamp may not light and the network connections may not be possible. In this case, disable the PoE device setting, and refer to the operating instructions of the PoE device in use.

When the LAN cable is disconnected once, reconnect the cable after about 2 seconds.

When the cable is quickly reconnected, the power may not be supplied from the PoE device.

27

Image 27
Contents Model No. WV-SW458/WV-SW458M WV-SW458E/WV-SW458ME WV-SW458E, WV-SW458ME Contents Important safety instructions Limitation of liability Disclaimer of warrantyPreface About notationsMain functions CPU System requirements for a PCCopyright Trademarks and registered trademarksNetwork security Precautions Cleaning this product body Do not damage the power cableTurn the power off when cleaning this product Precautions for use This product has no power switchIndication label Mount bracket accessory SW458Code label Discoloration on the color filter of the MOS image sensorAbout the network connection Precautions for installationInstalling place Do not place this product in the following placesRouter Time & date settingProcure fixing screws separately Radio disturbanceMajor operating controls About the Initial SET button About the indicators inside the SD memory card slot coverPreparations Mounting hole pattern Using the side cable access hole SW458MInstalling the camera directly on the ceiling or wall SW458M Using the mount bracket accessory SW458 Ø1-1/16 inches Cable access hole For use of the hole Camera attachment accessory Fixing screws accessory Insert/remove an SD memory card WV-SW458M Power cableConnection WV-SW458Alarm OUT, AUX OUT AlarmRatings Terminal name When using PoE IEEE802.3af compliant When using 12 V DC power supply*1LAN cable How to wind the supplied waterproof tapeRequired cable Using a two-gang junction box InstallationUsing the mount bracket SW458 Page Use the bit for tamperproof screw accessory Configuring the camera so that it can be accessed from a PC Configure the network settingsPage When using DC power supply TroubleshootingBasic SpecificationsLimited Power Source Alarm in 1, Alarm in 2/ Alarm OUTELC ATW1/ ATW2/ AWCViqs Lens NetworkJpeg IGMP, ICMP, ARP Jpeg MjpegOptional accessories Standard accessoriesPage Page For business users in the European Union For U.S. and CanadaPGQX1203YA