Axis Communications Q1635 user manual Network, Basic TCP/IP Settings

Page 52

AXIS Q1635 Fixed Network Camera

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 61) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 52.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Axis Q1635 Fixed Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1635 Fixed Network CameraConnectors Performance Considerations Hardware Overview Connectors and Buttons Network ConnectorConnector Power ConnectorLED Indicators Buzzer Signal for Focus Assistant Status LED Behavior for Focus AssistantReplace the Lens Access from a Browser Access the ProductAccess from the Internet Set the Root Password Set Power Line FrequencyPTZ Mode Configure Capture ModeControls on the Live View Go to Setup EventsManual Trigger Axis Media Control viewer toolbar PTZ ControlsTo show the manual trigger buttons in the Live View AMC Audio ControlsAxis Q1635 Fixed Network Camera Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingBasic Setup Set Up the ProductAdjust Focus Focus Assistant Set Up Video Streams Video and AudioPixel Counter ImageClick Save to apply the new settings 264Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Stream ProfilesImage Correction Image AppearanceWhite Balance Exposure Settings Wide Dynamic RangeShutter & Gain Set Shutter toIris configuration Iris adjustmentImage Settings View AreaSelect an Aspect ratio and a Video stream resolution OverlayOverlay Image Go to Video & Audio View AreaUse Overlay Text in an Action Rule Go to Video & Audio Overlay ImageGo to Events Action Rules Click Add to create a new rulePrivacy Mask FocusBasic AdvancedAudio Modes Set Up AudioAudio Input Audio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedOperator Same as administrator but with lower priority Install PTZ DriverControl Queue Detectors Camera TamperingShock Detection Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionRecommended values 15% 60-90% 75-95%Install Application Go to Setup ApplicationsApplications Application LicensesAxis Q1635 Fixed Network Camera Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemAdd Recipients ActionsRecipient Types PTZ ControlSet Up Email Recipients Recipient Use with actionSet Up Recurrences Create SchedulesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages System Options SecurityUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time Audio SupportBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 Storage BonjourSD Card Mount and Unmount SD CardPorts & Devices Network SharePorts COM PortMaintenance Port StatusAccelerometer See the online helpSupport Reset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Function/group Specifications Audio Audio streaming Specification Network SecurityAudio input Audio outputFunction/group Specifications PowerConnectors WeightConnectors WarrantyFunction Pin Specifications PortuguesePin terminal block for power input Mm audio connectors stereo Tip Ring SleeveMicrophone/Line Ground Line out mono GroundRS485/422 Connector RX pair for all modes combined RX/TX for 2-wire RS485Performance Considerations Function PinM1.8
Related manuals
Manual 24 pages 60.17 Kb
Top Page Image Contents