Axis Communications Q1635 user manual LED Indicators

Page 8

AXIS Q1635 Fixed Network Camera

Hardware Overview

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal.

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

RS485/RS422 Connector

Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices.

SD Card Slot

NOTICE

•Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card.

•Risk of data loss. To prevent data corruption, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

This product supports microSD/microSDHC/microSDXC card (not included).

For SD card recommendations, see www.axis.com

Control Button

For location of the control button, see Hardware Overview on page 6 .

The control button is used for:

•Resetting the product to factory default settings. See page 61.

•Connecting to an AXIS Video Hosting System service. See page 53. To connect, press and hold the button for about 3 seconds until the Status LED flashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 53. To connect, press and hold the button for about 3 seconds.

Function Button

The function button has multiple functions:

•Levelling assistant – This function helps to ensure the camera is level. Press the button for about 3 seconds to start the levelling assistant and press again to stop the leveling assistant. The status LED (see ) and buzzer signal (see page 9 ) assist levelling of the camera. The camera is level when the buzzer beeps continuously.

•Focus assistant – This function is used for enabling the Focus Assistant. To enable the focus assistant, press and very quickly release the button. Press again to stop the focus assistant. For more information, see the Installation Guide.

LED Indicators

Note

•The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED. See the online help for more information.

•The Status LED can be configured to flash while an event is active.

•The Status LED can be configured to flash for identifying the unit. Go to Setup > System Options > Maintenance .

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Axis Q1635 Fixed Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1635 Fixed Network CameraConnectors Performance Considerations Hardware Overview Connectors and Buttons Network ConnectorConnector Power ConnectorLED Indicators Buzzer Signal for Focus Assistant Status LED Behavior for Focus AssistantReplace the Lens Access from the Internet Access the ProductAccess from a Browser Set the Root Password Set Power Line FrequencyPTZ Mode Configure Capture ModeManual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbar PTZ ControlsTo show the manual trigger buttons in the Live View AMC Audio ControlsAxis Q1635 Fixed Network Camera Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingAdjust Focus Set Up the ProductBasic Setup Focus Assistant Set Up Video Streams Video and AudioPixel Counter ImageClick Save to apply the new settings 264Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Stream ProfilesWhite Balance Image AppearanceImage Correction Exposure Settings Wide Dynamic RangeShutter & Gain Set Shutter toIris configuration Iris adjustmentImage Settings View AreaSelect an Aspect ratio and a Video stream resolution OverlayOverlay Image Go to Video & Audio View AreaUse Overlay Text in an Action Rule Go to Video & Audio Overlay ImageGo to Events Action Rules Click Add to create a new rulePrivacy Mask FocusBasic AdvancedAudio Input Set Up AudioAudio Modes Audio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedControl Queue Install PTZ DriverOperator Same as administrator but with lower priority Detectors Camera TamperingShock Detection Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionRecommended values 15% 60-90% 75-95%Install Application Go to Setup ApplicationsApplications Application LicensesAxis Q1635 Fixed Network Camera Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemAdd Recipients ActionsRecipient Types PTZ ControlSet Up Email Recipients Recipient Use with actionSet Up Recurrences Create SchedulesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages System Options SecurityUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time Audio SupportBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM Storage BonjourSD Card Mount and Unmount SD CardPorts & Devices Network SharePorts COM PortMaintenance Port StatusAccelerometer See the online helpSupport Reset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Function/group Specifications Audio Audio streaming Specification Network SecurityAudio input Audio outputFunction/group Specifications PowerConnectors WeightConnectors WarrantyFunction Pin Specifications PortuguesePin terminal block for power input Mm audio connectors stereo Tip Ring SleeveMicrophone/Line Ground Line out mono GroundRS485/422 Connector RX pair for all modes combined RX/TX for 2-wire RS485Performance Considerations Function PinM1.8
Related manuals
Manual 24 pages 60.17 Kb
Top Page Image Contents