Axis Communications Q1635 Storage, Bonjour, Mount and Unmount SD Card, Format SD Card

Page 57

AXIS Q1635 Fixed Network Camera

System Options

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent data corruption, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

The Axis product supports microSD cards with up to 64 GB of storage. For best recording performance, use ultra-high speed microSD cards (microSDHC UHS-I or microSDXC UHS-I).

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select Lock under General Settings.

Mount and Unmount SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Open the Axis product’s webpages and go to Setup > System Options > Storage.

2.Click SD Card.

3.Click Unmount.

4.The card can now be removed.

Format SD Card

NOTICE

Formatting the SD card will remove all data and recordings stored on the card.

57

Image 57

Contents Axis Q1635 Fixed Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis Q1635 Fixed Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Network Connector Connectors and ButtonsConnector Power ConnectorLED Indicators Status LED Behavior for Focus Assistant Buzzer Signal for Focus AssistantReplace the Lens Access the Product Access from a BrowserAccess from the Internet Set Power Line Frequency Set the Root PasswordPTZ Mode Configure Capture ModeGo to Setup Events Controls on the Live ViewManual Trigger PTZ Controls Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View AMC Audio ControlsAxis Q1635 Fixed Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsSet Up the Product Basic SetupAdjust Focus Focus Assistant Video and Audio Set Up Video StreamsPixel Counter Image264 Click Save to apply the new settingsCapture Mode Camera SettingsGo to Setup Video & Audio Camera Settings Stream ProfilesImage Appearance Image CorrectionWhite Balance Wide Dynamic Range Exposure SettingsShutter & Gain Set Shutter toIris adjustment Iris configurationImage Settings View AreaOverlay Select an Aspect ratio and a Video stream resolutionOverlay Image Go to Video & Audio View AreaGo to Video & Audio Overlay Image Use Overlay Text in an Action RuleGo to Events Action Rules Click Add to create a new ruleFocus Privacy MaskBasic AdvancedSet Up Audio Audio ModesAudio Input Audio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onPTZ Pan Tilt Zoom Preset PositionsGuard Tour AdvancedInstall PTZ Driver Operator Same as administrator but with lower priorityControl Queue Camera Tampering DetectorsShock Detection Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAudio Detection Default valuesRecommended values 15% 60-90% 75-95%Go to Setup Applications Install ApplicationApplications Application LicensesAxis Q1635 Fixed Network Camera Events Set Up Action RulesTriggers Go to Events Action Rules and click AddHardware Input SignalStorage SystemActions Add RecipientsRecipient Types PTZ ControlRecipient Use with action Set Up Email RecipientsCreate Schedules Set Up RecurrencesTo create a new schedule Go to Events Schedules and click AddRecording List RecordingsContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages Security System OptionsUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Click Install certificate and upload the certificate Go to Setup System Options Security CertificatesDate & Time Audio SupportNetwork Basic TCP/IP SettingsAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 Bonjour StorageSD Card Mount and Unmount SD CardNetwork Share Ports & DevicesPorts COM PortPort Status MaintenanceAccelerometer See the online helpSupport Plain Config Reset to Factory Default SettingsUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Problems with streaming H.264Video and image problems, general Setup Video & Audio Camera SettingsStorage and disk management problems SettingsNo audio Poor audio qualityTechnical Specifications Specification Network Security Function/group Specifications Audio Audio streamingAudio input Audio outputPower Function/group SpecificationsConnectors WeightWarranty ConnectorsFunction Pin Specifications PortugueseMm audio connectors stereo Tip Ring Sleeve Pin terminal block for power inputMicrophone/Line Ground Line out mono GroundRX pair for all modes combined RX/TX for 2-wire RS485 RS485/422 ConnectorPerformance Considerations Function PinM1.8

Related manuals

Manual 24 pages 60.17 Kb