Axis Communications Q1635 user manual UPnPTM, RTP/H.264

Page 56

AXIS Q1635 Fixed Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 49. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 61.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

56

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Axis Q1635 Fixed Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1635 Fixed Network CameraConnectors Performance Considerations Hardware Overview Connectors and Buttons Network ConnectorConnector Power ConnectorLED Indicators Buzzer Signal for Focus Assistant Status LED Behavior for Focus AssistantReplace the Lens Access from the Internet Access the ProductAccess from a Browser Set the Root Password Set Power Line FrequencyPTZ Mode Configure Capture ModeManual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbar PTZ ControlsTo show the manual trigger buttons in the Live View AMC Audio ControlsAxis Q1635 Fixed Network Camera Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingAdjust Focus Set Up the ProductBasic Setup Focus Assistant Set Up Video Streams Video and AudioPixel Counter ImageClick Save to apply the new settings 264Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Stream ProfilesWhite Balance Image AppearanceImage Correction Exposure Settings Wide Dynamic RangeShutter & Gain Set Shutter toIris configuration Iris adjustmentImage Settings View AreaSelect an Aspect ratio and a Video stream resolution OverlayOverlay Image Go to Video & Audio View AreaUse Overlay Text in an Action Rule Go to Video & Audio Overlay ImageGo to Events Action Rules Click Add to create a new rulePrivacy Mask FocusBasic AdvancedAudio Input Set Up AudioAudio Modes Audio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedControl Queue Install PTZ DriverOperator Same as administrator but with lower priority Detectors Camera TamperingShock Detection Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionRecommended values 15% 60-90% 75-95%Install Application Go to Setup ApplicationsApplications Application LicensesAxis Q1635 Fixed Network Camera Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemAdd Recipients ActionsRecipient Types PTZ ControlSet Up Email Recipients Recipient Use with actionSet Up Recurrences Create SchedulesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages System Options SecurityUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time Audio SupportBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM Storage BonjourSD Card Mount and Unmount SD CardPorts & Devices Network SharePorts COM PortMaintenance Port StatusAccelerometer See the online helpSupport Reset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Function/group Specifications Audio Audio streaming Specification Network SecurityAudio input Audio outputFunction/group Specifications PowerConnectors WeightConnectors WarrantyFunction Pin Specifications PortuguesePin terminal block for power input Mm audio connectors stereo Tip Ring SleeveMicrophone/Line Ground Line out mono GroundRS485/422 Connector RX pair for all modes combined RX/TX for 2-wire RS485Performance Considerations Function PinM1.8
Related manuals
Manual 24 pages 60.17 Kb
Top Page Image Contents