Bosch Appliances user manual VEZ-400 Mini PTZ Dome Installing a Surface Mount en

Page 21

VEZ-400 Mini PTZ Dome	Installing a Surface Mount en 21

screws enough to ensure that the camera base is secured to the ceiling.

11.Make the necessary Dip Switch settings (described in chapter 4.3). Note: This step can also be done later, but then the dome cover must be re-opened.

CAUTION!

When (re)mounting the dome cover to the camera base, make sure that each screw has a rubber O-ring, and that the large rubber O-ring is in place on the camera base. This ensures protection against water ingress.

12.Align the screw holes on the dome cover (item 6) with the camera base.

13.Attach the dome cover to the camera base using the four M4 x 12 Torx screws (with O-rings (item 4) attached) using the supplied Torx wrench. Make sure that the large rubber O-ring between the camera base and dome cover is in place to protect the camera against water ingress. Tighten the screws enough to ensure that the housing is secured to the camera base and that the rubber O-rings seal the dome cover against water ingress.

14.Remove the plastic film protecting the dome cover from scratches.

Bosch Security Systems, Inc.

User Manual

F.01U.252.635 2.0 2011.09

Image 21

Contents VEZ-400 Mini PTZ Dome Page Table of Contents WDR/DNR Safety precautions SafetyImportant safety instructions Important notices Coax grounding Rack mount FCC & Ices Information FCC & Ices complianceModèles utilisés aux États-Unis et au Canada uniquement Informations FCC et IcesEn Safety VEZ-400 Mini PTZ Dome Disclaimer Bosch noticesCopyright TrademarksMore information Description FeaturesParts List UnpackingQty Description Accessories Additional Tools RequiredModel Number Description Drawing Installation Overview Number Description Installing a Surface MountEn Installing a Surface Mount VEZ-400 Mini PTZ Dome VEZ-400 Mini PTZ Dome Installing a Surface Mount en Connection RS-485 Connections Typical wiring configurationTRX Number Signal ColorAlarm Connections Video ConnectionAWG Power Connections Camera Settings16AWG SW301 Rotary switch SW303 Dip switches SW302 Rotary switch Setting the protocol of the camera Setting the address ID of the cameraNo1 No2 Protocol No3 No4 Baud Rate bpsBasic Navigation and Common Actions On-Screen Display OSD MenuVEZ-400 Mini PTZ Dome CAM Test ...PASSKEY Command ActionMain Menu System SetupMain Menu Main Menu Choices DescriptionEditing Titles Menu DescriptionTitle System Setup System Setup MenuClearing Saved Functions System InformationReboot RebootInitialize System InformationPassword ALL CAM Preset Tour Pattern Scan ETC Save BackInitialize OSD Setup Display SetupPassword Display SetupPrivacy Zone OSD SetupSelect Privacy ZONE. The screen Privacy Zone Setup appears Privacy Zone SetupPRIVACY.## Edit Display Width Height Clear Save Back Change Image Setup Image SetupMotion/Face Detection Mirror Save BackLanguage MD/FD Sensitivity Alarm Atime Save BackMOTION/FACE Detection OSDCamera Setup Camera SetupSelect FOCUS/ZOOM. The screen FOCUS/ZOOM Setup appears Focus/ZoomWB Setup FOCUS/ZOOM SetupFocus Zoom SPD Save Back AE Setup WB SetupMode Gain B Gain Save Back AE Setup 4 D/N SetupMode Shut AGC Gain AGC MAX DSS Bright Save Back AE Mode Full Auto ManualSetup AdvancedDAY/NIGHT Detect Dtime Save Back Advanced Setup Select ADVANCED. The screen Advanced Setup appears6 WDR/DNR Sharpness Backlight SaveWDR Setup WDR Level DNR Setup DNR Level Save Back Dome Motion SetupDome Motion Setup General Setup Motion Setup Home Action Calibration ExitMotion Setup General SetupSelect General SETUP. The screen General Setup appears General SetupMotion Setup Select Motion SETUP. The screen Motion Setup appearsHome Action Prop PAN/TILT Auto Flip Over Tilt Save BackSelect Home ACTION. The screen Home Action Setup appears Home Action SetupAction Number Time Mode Save Back Calibration Setup Select CALIBRATION. The screen Calibration Setup appearsAuto CAL Error MSG Disp Calibration Save Back CalibrationPreset Setup Preset SetupEdit Title Time Clear Save Back Pattern Setup Pattern SetupTour Setup Tour SetupTOUR1 Preset only Save Back Change ID Change ACT Clear ID Scan Setup Scan SetupEdit Speed Dtime Direction Mode Clear Save Back Alarm Setup Alarm SetupOUT Priority Action Number Atime Save Back SET/CLEAR Problem Solution TroubleshootingVEZ-400 Mini PTZ Dome Troubleshooting en Camera Module Technical SpecificationsWDR DNRNC/NO MechanicalEnvironment Dimensions Camera DimensionsBosch Protocol Preset Key Example NumberEn Bosch Protocol VEZ-400 Mini PTZ Dome Pelco Protocol Preset Key Operation Example NumberEn Pelco Protocol VEZ-400 Mini PTZ Dome Page Bosch Security Systems, Inc