Panasonic WV-NW470S Image Adjustment, Video Output Connection, Control Connector, Tions

Page 12

●Video Output Connection

Connect the video output cable to the monitor or other system device with the procured coaxial cable. The maximum extensible length is shown in the table.

	Type of		RG-59/U	RG-6/U	RG-11/U	RG-15/U
	coaxial cable		(3C-2V)	(5C-2V)	(7C-2V)	(10C-2V)

	Recommended	(m)	250	500	600	800
	maximum
	maximum	(ft)	825	1650	1 980	2 640
	cable length	(ft)	825	1650	1 980	2 640

●Control Connector

Connect the respective peripherals to supply and receive control signals. Use the supplied 5-pin cable adapter. For electrical ratings, refer to SPECIFICA-

TIONS.

	Pin#	Wire colour	Function	Example of
	Pin#	Wire colour	Function	peripherals
				peripherals

	1	Black	Alarm in	Door switch

	2	Grey	Alarm out	Buzzer

	3	Pink	AUX out	Lighting lamp

	4	Red	Day/night in	Optical sensor

	5	Green	GND	Signal ground

●Network Port Connection

Connect the network port to a PC or a network via a hub with a 10BASE-T/100BASETX cable. Use the sup- plied adapter (RJ-45, female-female) if necessary.

Note: For network system connections, refer to ■ Network Connection Types.

■Image Adjustment

You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected moni- tor.

Notes:

•Do not hold the camera by the lens unit when adjusting panning, tilting, or azimuth.

•The video output to the BNC will be interrupted while an LCD monitor is connected to the monitor output jack.

1.Connect an LCD monitor to the video jack.

2.Pan/tilt/azimuth adjustment

•Loosen the two screws locking the pan and tilt tables.

•Pan and tilt the table to aim the camera at what you need to watch.

•Turn the azimuth adjuster to obtain a level image.

•Tighten the two screws after adjustment.

Variable angles plus or minus 75° (max.)

Monitor output jack

Pan lock screw Panning table

Tilting lock screw

Azimuth adjuster

-12-

Image 12

Contents WV-NW474SE Risk of Electric Shock Do not Open Contents Features PrefaceSystem Requirements TrademarksDocument Convention Precautions Handle the camera with careNever face the camera towards the sun Do not aim the camera at the same object for a long timeMajor Operating Controls & Their Functions 8DIP switch @3Control connector@4Power cable @2Video output connectorInstallation Installation Plans & PreparationsInstallation space ProcurementMounting the Camera Optional Heater UnitPower Connection Wire colours & functions AC TypeCable length and wire gauge 24 V AC Type ConnectionsImage Adjustment Control ConnectorVideo Output Connection Network Port ConnectionWaterproof Process Network Connection Types Direct Connection to PC TypeConnection to Intranet Type Connection to Internet TypeNetwork Setup of Your PC Preparations for Network ConnectionsNetwork Setup of the Camera Using Panasonic IP Setup SoftwareDhcp DNS DdnsPage Prior to Camera Setup Buttons Used for SetupCamera Setup Menus ALL Reset button¡From the Camera Setup Menu Tree Setting Procedures Setup SelectionCamera Setup Menu CAM Camera Identification Camera ID SettingLight Control Setting ALC Command UsageTo edit the Camera ID To replace a specific character in the Camera IDGain Control Setting AGC on DNR-L, DNR-H/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Setting Sync White Balance Setting White BALATW1 Auto-Tracing White Balance Motion Detector Setting Motion DET Automatic White Balance Control Mode AWCManual Fine Adjustment for AWC ATW Push SWMenu/DIP SW Selection Special Menu SpecialTo reset to the factory settings Camera Reset 10-6. BWNetwork Setup Network Setup Http Port NumberInitializing the Setup Menu InitializingInitializing the Camera Menu Initializing Html FilesTroubleshooting Specifications TCP/IP, HTTP, FTP, SMTP, DNS, DDNS, DHCP, ARP, BOOTP, NTPPrevention of Blooming and Smear Network SectionStandard Accessories Optional AccessoriesGeneral WV-NW474SEAppendix Optional Heater Unit WV-CW3HE在日本印刷