Synchronization Setting Sync | Panasonic WV-NW474SE, WV-NW470S

6. Synchronization Setting (SYNC)

There are three synchronization modes: INT (internal),

LL(line-lock), and VD2 (vertical drive). You can select the internal or line lock mode in the menu setup, but you cannot select VD2. The VD2 signal is supplied from an external device e.g., a Video Multiplexer, by being multiplexed on a coaxial cable, and it overrides the internal and line-lock mode even when these modes are selected in the menu.

Note: The priority for sync sources is: VD2 (highest) – LL – INT (lowest).

1.Move the cursor to SYNC and select a mode.

INT: Synchronizes the camera to the internal gener- ator.

LL: Synchronizes to 24 V AC or 220 V - 240 V AC. The default setting is INT.

2.When LL is selected, press [SET] to open a sub- menu.

The vertical phase can be adjusted in the submenu.

** SYNC **

V PHASE
COARSE
COARSE		1	(1--16)
FINE	I
	-	+

RET END

3.Supply the video output signal of the camera to be adjusted and the reference camera video output signal to a dual-trace oscilloscope.

4.Set the oscilloscope to the vertical rate and expand the vertical sync portion on the oscilloscope.

5.Move the cursor to COARSE. The cursor is highlight- ed.

6.Press [Left] or [Right] to match the vertical phase for both video output signals as closely as possible. (COARSE adjustment can be incremented in 16 steps by 22.5 degrees by pressing [Left] or [Right].) Note: After the sixteenth step, the adjustment

returns to the first step.

1 (1 - - 16): 0 degrees

2 (1 - - 16): 22.5 degrees

16 (1 - - 16): 337.5 degrees

7.Move the cursor to FINE.

8.Press [Left] or [Right] to match the vertical phase for both video output signals as closely as possible.

(FINE adjustment can be made by up to 22.5 degrees by pressing [Left] or [Right].)

Notes:

•When the "I" cursor reaches the "+" end, it jumps back to "–". At the same time, COARSE is incre- mented by one step to enable a continuous adjustment. The reverse takes place when the "I" cursor reaches the "–" end.

•When [Left] or [Right] is kept pressed for a sec- ond or more, the "I" cursor moves faster.

•To reset COARSE and FINE to the values preset at the factory, press [Left] and [Right] simultane- ously. COARSE and FINE adjustments are preset at the factory to zero-crossing of the AC line phase.

•If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of the camera video output signal may be disturbed.

7.White Balance Setting (WHITE BAL)

You can select one of four modes for white balance adjustment as follows.

The factory default setting is ATW1.

•ATW1 (Auto-Tracing White Balance 1)

Move the cursor to WHITE BAL and select ATW1.

In this mode, the colour temperature is monitored continuously and thereby white balance is automati- cally set. The colour temperature range for the prop- er white balance is approximately 2 600 - 6 000 K. Proper white balance may not be obtained under the following conditions:

** CAM SET UP **

CAMERA ID	OFF	↵
ALC	ALC	↵
SHUTTER	---
AGC	ON(DNR-H)
SENS UP	OFF
SYNC	INT
WHITE BAL	ATW1↵
MOTION DET	OFF

RET END

1.The colour temperature is out of the 2 600 - 6 000 K range.

2.When the scene contains mostly high colour temper- ature objects, such as a blue sky or sunset.

3.When the scene is dim.

In these cases, select the AWC mode.

•ATW2 (Auto-Tracing White Balance 2) Auto-tracing white balance in the sodium lamp mode (ATW2)

When you select ATW2 for sodium lamp, white bal- ance is automatically set (no operation needed).

Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup menu.

-25-