Panasonic WV-CS854B operating instructions Pan Offset, To Set the Lens Zoom and Focus Positions

Page 19

3.Pan Offset

If the camera is replaced with a new one, the pan offset function is used to adjust its positions to be the same as before except patrol setting.

The system controller can download or upload the preset position data.

Caution: The preset data for other cameras (WV- CS654 for example) is incompatible with WV- CS854B’s. WV-CS854B’s preset data will be destroyed if you upload the conventional data. If this happened, reset the WV-CS854B to the default settings. Download the factory settings into the controller and upload the correct preset data newly to the initialized WV-CS854B.

(1) Display the PRESET NUMBER SET menu.

** PRESET NUMBER SET **

 

1*

 

2

3

4

5

 

6

7

8

9

 

10

11

12

13

 

14

15

16

17

 

18

19

20

21

 

22

23

24

25

 

26

27

28

29

 

30

31

32

 

ID:DOOR

 

 

33-64

RET

 

 

(2)Select a position number for the picture to be most enlarged among the numbers with the joystick. Then press the CAM (SET) key. The position setting menu appears.

(3)Move the cursor to PAN OFFSET SET and select the right or left arrow with the joystick.

** POSITION 1 **

PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET

PAN OFFSET SET ← −0.0

RET

FLOOR1

DOOR

(4)Press the CAM (SET) key until the desired offset value appears.

(5)Move the cursor to an item other than PAN OFFSET SET, and press the MON (ESC) key.

Notes:

Further adjustment of the other positions is unnecessary. This adjustment applies to all other positions.

Make sure to move the cursor before pressing the key in step 5. Otherwise the settings will be ignored.

Retry the loading when the camera fails to upload or download the data.

4. To Set the Lens Zoom and Focus Positions

(1)Move the cursor to PUSH SET for ZOOM/FOCUS and press the CAM (SET) key. The ZOOM/FOCUS setting menu appears.

** POSITION 1 **

PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET

PAN OFFSET SET ← −0.0

RET

FLOOR1

DOOR

(2)Select a zoom position by moving the zoom control up and down and a focus position by moving the focus control up and down, and then press the CAM (SET) key.

 

** POSITION 1 **

 

PAN/TILT

PUSH

SET

 

ZOOM/FOCUS

PUSH

SET

 

 

 

 

 

 

 

PAN

U ZOOM D/L FOCUS R

 

OFFSET SET ← −0.0

RET

FLOOR1

DOOR

The positions are set and the screen returns to the position setting menu.

Notes:

When the camera is used at a nearly horizontal angle, the focus may not be adjustable to a high level of accuracy.

If you move the cursor to the position number and move the joystick right or left, the position number can be selected.

The selected preset position number can also be set after pressing the CAM (SET) key.

The preset and camera IDs appear in the lower- left corner of the position setting menu after setting them.

5.Move the cursor to RET and press the CAM (SET) key to return to the preset setting menu.

** POSITION 1 **

PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET

PAN OFFSET SET ← −0.0

RET

FLOOR1

DOOR

-19-

Image 19
Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Preface FeaturesDigital Flip Operation Camera Cleaning PrecautionsPreset Data Uploading or Down Loading Prevention of blooming and smear ConsumablesDo not aim the camera at the same object for a long time Self-diagnosis FunctionConstruction Setup Menu SetupAUTO/ON/OFF P Prog SW Preset IDMON ESC CAM SET WV-CU161C WV-RM70Setup Menu Description Camera Important Notices Shutter Speed ShutterGain Control AGC Synchronization Sync11Self-diagnosis Function Auto Focus AF ModeRS485 Communication 10Special 2 Menu SPECIAL2Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions Preset MenuPreset Menu Display Position Setting Position SETTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Dwell Time Dwell Time Light Control Setting ALC/MANUALScene File Setting Scene File To Return to the Preset Setting MenuTo Return to the Setup Menu Deleting Preset PositionsPreset Speed Setting Preset Speed To Return to the Preset Number Set MenuOFF SEQ Sort Auto PAN Patrol Home Position Setting HomeSelf Return Setting Self Auto Mode Selection AutoZoom →PUSH SET RET Digital Flip Setting Digital Flip Auto Pan Key Setting Auto PAN KEYSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialZoom ratio Settings for on NeswProportional Pan/Tilt PROPO. P/T Area Title Area TitleArea Title Editing Setting for on UserPAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White Balance Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol Learn with a Controller Having Patrol KeyPatrol Play with the Auto PAN Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyElectronic Zoom EL-ZOOM Cleaning CleaningCNT-CLS 1, 2 Output Image Hold Image Hold Preset Alarm Preset ALMTilt Angle Tilt Angle 0 /5 To Display the Camera Setting Menu Camera SettingCamera Identification Camera ID ALC Mode with SUPER-D2 on Gain Control AGC on LOW/ MID/ HIGH/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAutomatic White Balance Control Mode AWC Auto-Tracing White Balance Mode ATW1/ ATW2White Balance White BAL Motion Detector Motion DET Auto S Auto M Auto L Manual L Manual M Manual S Auto Focus Setting AF ModeResolution Resolution Special 2 Menu SPECIAL2Burst BW Setting Black and White Mode BW ModeBW Setting PIX Sens UP SettingReset to the Factory Default Settings PIX OFF Setting PIX OFFCamera Resetting Camera Reset To Restore the Camera Default Position RefreshInitial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters CNT-CLS OFF Coax ALM OUT Factory Default SettingMenu Setting Preset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell TimeRS485 Parameter Setup InstallationSetting the Switches PrecautionsUnit Number For Panasonic’s ProtocolUnit Assemble the Camera RS485 SettingSideway Cable Exit Hook the fall prevention wire on the camera mounting base Connections Accessory Connector InformationHow to Assemble the Cable with the Accessory Connector Connect this to 24 V AC Class 2 Power Supply onlyOUT Alarm in ConnectionsAlarm OUT Connections RS485 ConnectionSystem Connections WV-CS854B SpecificationsOptional Accessories AccessoriesWV-CS2SH Shortcuts AppendixImprimé au Japon