Panasonic WV-CS854B RS485 Connection, Alarm in Connections, Alarm OUT Connections, Out, Gnd

Page 51

•RS485 Connection

Data transmission

Data reception

Brown

Red

Orange

Yellow

Green

GND

T(B) T (A) R (B) R (A)

Note:

Use the cable that is described below for RS485 site communication.

•Shielded, twisted pair cable

•Low impedance

•Wire gauge size is thicker than AWG #22 (0.33 mm2).

•ALARM IN Connections

An 8-pin and a 4-pin harness are supplied with the camera as standard accessories. Connect external sensors to this connector. Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). The table below shows wire colors versus pin functions.

Alarm OUT (4-pin)

Wire color	Function

Grey	OUT 1
White	GND
Pink	OUT 2
Yellow green or light blue	GND

Note: Use a relay if the voltage or current of the connected device exceeds the ratings.

	Alarm IN (8-pin)
Wire color		Function

Black		IN 1
Brown		GND
Red		IN 2
Orange		GND
Yellow		IN 3
Light blue or green		GND
Blue		IN 4
Purple		GND

•ALARM OUT Connections

Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are low-active, open-collector and a drive capacity of 16 V DC 100 mA maximum. The table below shows wire colors versus pin functions.

-51-

Image 51

Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Features PrefaceDigital Flip Operation Precautions Camera CleaningPreset Data Uploading or Down Loading Prevention of blooming and smear ConsumablesDo not aim the camera at the same object for a long time Self-diagnosis FunctionConstruction Setup Menu SetupAUTO/ON/OFF P Prog SW Preset IDMON ESC CAM SET WV-CU161C WV-RM70Setup Menu Description Camera Important Notices Shutter Speed ShutterGain Control AGC Synchronization Sync11Self-diagnosis Function Auto Focus AF ModeRS485 Communication 10Special 2 Menu SPECIAL2Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions Preset MenuPreset Menu Display Position Setting Position SETTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Dwell Time Dwell Time Light Control Setting ALC/MANUALScene File Setting Scene File To Return to the Preset Setting MenuTo Return to the Setup Menu Deleting Preset PositionsPreset Speed Setting Preset Speed To Return to the Preset Number Set MenuOFF SEQ Sort Auto PAN Patrol Home Position Setting HomeSelf Return Setting Self Auto Mode Selection AutoZoom →PUSH SET RET Auto Pan Key Setting Auto PAN KEY Digital Flip Setting Digital FlipSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialZoom ratio Settings for on NeswProportional Pan/Tilt PROPO. P/T Area Title Area TitleArea Title Editing Setting for on UserPAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White Balance Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol Learn with a Controller Having Patrol KeyPatrol Play with the Auto PAN Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyCleaning Cleaning Electronic Zoom EL-ZOOMCNT-CLS 1, 2 Output Preset Alarm Preset ALM Image Hold Image HoldTilt Angle Tilt Angle 0 /5 Camera Setting To Display the Camera Setting MenuCamera Identification Camera ID ALC Mode with SUPER-D2 on Shutter Speed Setting Shutter Gain Control AGC on LOW/ MID/ HIGH/OFFElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAuto-Tracing White Balance Mode ATW1/ ATW2 Automatic White Balance Control Mode AWCWhite Balance White BAL Motion Detector Motion DET Auto S Auto M Auto L Manual L Manual M Manual S Auto Focus Setting AF ModeResolution Resolution Special 2 Menu SPECIAL2Burst BW Setting Black and White Mode BW ModeBW Setting PIX Sens UP SettingReset to the Factory Default Settings PIX OFF Setting PIX OFFCamera Resetting Camera Reset To Restore the Camera Default Position RefreshRS485 Setup Initial Camera Communication ParametersChanging the Camera Communication Parameters CNT-CLS OFF Coax ALM OUT Factory Default SettingMenu Setting Preset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell TimeRS485 Parameter Setup InstallationSetting the Switches PrecautionsUnit Number For Panasonic’s ProtocolUnit RS485 Setting Assemble the CameraSideway Cable Exit Hook the fall prevention wire on the camera mounting base Connections Accessory Connector InformationHow to Assemble the Cable with the Accessory Connector Connect this to 24 V AC Class 2 Power Supply onlyOUT Alarm in ConnectionsAlarm OUT Connections RS485 ConnectionSystem Connections WV-CS854B SpecificationsAccessories Optional AccessoriesWV-CS2SH Shortcuts AppendixImprimé au Japon