Panasonic WV-CS854B operating instructions RS485 Setting, Assemble the Camera, Sideway Cable Exit

Page 48

RS485 Setting

The 4-bit DIP switch is used for RS485 termination.

4-bit DIP SW

ON

1

2

3

4

BP 1

Function

Switch

ON

Termination ON

position

OFF

Termination OFF *

BP 2

BP 3

BP 4

Function

Switch

ON

ON

ON

Half duplex (2 line)

position

OFF

OFF

OFF

Full duplex (4 line) *

Notes:

•Defaults are marked with *.

•BP stands for Bit Position.

•Full duplex is not available in a daisy chain connection. (Panasonic system controllers only)

3.Assemble the Camera

Reverse the disassembly procedure. Take care not to cut any cables.

Precaution: Be sure to select a ceiling board strong enough to support 4 times the total weight of the camera.

a.Sideway Cable Exit

Prepare a cutout in the diecast case and decoration cover as shown in the following figures.

Cutout in Diecast Case

Cutout in Decoration Cover

Note: Remove sharp edges to protect the cables.

b.Top Cable Exit

Prepare a hole in the ceiling board to run the cables.

1.Mark the mounting holes on the ceiling, using the removed camera mounting base as a template.

Marking

2.Fix the camera mounting base to the ceiling with four screws (not provided, M4).

-48-

Image 48

Contents Color Cctv Camera English Version Important Safety Instructions EnglishPage Contents Features PrefaceDigital Flip Operation Precautions Camera CleaningPreset Data Uploading or Down Loading Consumables Do not aim the camera at the same object for a long timeSelf-diagnosis Function Prevention of blooming and smearConstruction Setup Setup MenuAUTO/ON/OFF P Preset ID MON ESC CAM SETWV-CU161C WV-RM70 Prog SWSetup Menu Description Camera Shutter Speed Shutter Gain Control AGCSynchronization Sync Important NoticesAuto Focus AF Mode RS485 Communication10Special 2 Menu SPECIAL2 11Self-diagnosis FunctionSetting Procedures Setup Menu DisplayMenu Display Submenu DisplayPreset Menu Preset Menu DisplayPosition Setting Position SET To Set Panning/Tilting PositionsPan Offset To Set the Lens Zoom and Focus PositionsPreset Identification Setting Preset ID Light Control Setting ALC/MANUAL Scene File Setting Scene FileTo Return to the Preset Setting Menu Dwell Time Dwell TimeDeleting Preset Positions Preset Speed Setting Preset SpeedTo Return to the Preset Number Set Menu To Return to the Setup MenuHome Position Setting Home Self Return Setting SelfAuto Mode Selection Auto OFF SEQ Sort Auto PAN PatrolZoom →PUSH SET RET Auto Pan Key Setting Auto PAN KEY Digital Flip Setting Digital FlipSEQ Sort Patrol New Password Password VerificationSpecial 1 Menu Setting Special Privacy Zone Privacy ZoneSettings for on Nesw Proportional Pan/Tilt PROPO. P/TArea Title Area Title Zoom ratioSetting for on User Area Title EditingPatrol-learn and Patrol Play Patrol To Quit EditingPatrol Learn with a Controller Having Patrol Key PAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White BalanceAlarm Input/Output Alarm IN/OUT Patrol Play with a Controller Having the Patrol KeyPatrol Play with a Controller not Having the Patrol Key Patrol Play with the Auto PAN KeyCleaning Cleaning Electronic Zoom EL-ZOOMCNT-CLS 1, 2 Output Preset Alarm Preset ALM Image Hold Image HoldTilt Angle Tilt Angle 0 /5 Camera Setting To Display the Camera Setting MenuCamera Identification Camera ID ALC Mode with SUPER-D2 on Shutter Speed Setting Shutter Gain Control AGC on LOW/ MID/ HIGH/OFFElectronic Sensitivity Enhancement Sens UP Line-lock Sync Mode LL Synchronization SyncAuto-Tracing White Balance Mode ATW1/ ATW2 Automatic White Balance Control Mode AWCWhite Balance White BAL Motion Detector Motion DET Auto Focus Setting AF Mode Resolution ResolutionSpecial 2 Menu SPECIAL2 Auto S Auto M Auto L Manual L Manual M Manual SBlack and White Mode BW Mode BW SettingPIX Sens UP Setting Burst BW SettingPIX OFF Setting PIX OFF Camera Resetting Camera ResetTo Restore the Camera Default Position Refresh Reset to the Factory Default SettingsRS485 Setup Initial Camera Communication ParametersChanging the Camera Communication Parameters Factory Default Setting Menu SettingPreset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell Time CNT-CLS OFF Coax ALM OUTInstallation Setting the SwitchesPrecautions RS485 Parameter SetupFor Panasonic’s Protocol Unit NumberUnit RS485 Setting Assemble the CameraSideway Cable Exit Hook the fall prevention wire on the camera mounting base Accessory Connector Information How to Assemble the Cable with the Accessory ConnectorConnect this to 24 V AC Class 2 Power Supply only ConnectionsAlarm in Connections Alarm OUT ConnectionsRS485 Connection OUTSystem Connections Specifications WV-CS854BAccessories Optional AccessoriesWV-CS2SH Appendix ShortcutsImprimé au Japon