Panasonic WV-CS854B Auto Pan Key Setting Auto PAN KEY, Digital Flip Setting Digital Flip

Page 25

(2)Move the cursor to ZOOM, press the CAM (SET) key, move the joystick to settle the ZOOM position and return to the AUTO PAN menu. The manual zoom operation is not available in the TELE direction beyond the settled zoom position.

 

** ZOOM LIMIT **

 

 

 

ZOOM

 

PUSH SET

 

 

 

 

 

 

 

U ZOOM D

 

RET

AUTO PAN: Assigns the auto panning function to the key.

SEQ: assigns the SEQUENCE function to the key.

SORT: assigns the SORT function to the key.

PATROL: assigns the PATROL PLAY function to the key.

Note: AUTO PAN LED on the controller does not light if something other than AUTO PAN is assigned. AUTO PAN does not stop with the AUTO PAN key.

If PASSWORD LOCK is set to ON, you cannot operate AUTO PAN, SEQ, SORT, and PATROL even by pressing the AUTO key.

OFF: Does not limit the manual zoom operation.

Notes:

When the panning, tilting, zooming or focusing in the SEQ, SORT or PATROL mode is controlled manually, the auto mode function should be cancelled.

To activate the auto mode, select the desired auto mode again or set a time for SELF RETURN in the SET UP menu.

When 0S is selected, the camera stops without dwelling and starts.

Auto refreshing may be activated during the patrol play or the auto mode to calibrate the lens position.

Auto Pan Key Setting (AUTO PAN KEY)

This is used for assigning one of the following auto functions to the AUTO key on the controller. Pressing the AUTO key activates the assigned function after this setting.

Move the cursor to AUTO PAN KEY and select an auto function with the joystick.

The factory default setting is AUTO PAN.

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF AUTO PAN KEY AUTO PAN DIGITAL FLIP ON SPECIAL1

CAMERA

RS485 SET UP

PASSWORD LOCK OFF

The mode changes as follows:

SEQ SORT PATROL

AUTO PAN

Digital Flip Setting (DIGITAL FLIP)

Move the cursor to DIGITAL FLIP and select ON or OFF with the joystick.

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF AUTO PAN KEY AUTO PAN DIGITAL FLIP ON SPECIAL1

CAMERA

RS485 SET UP

PASSWORD LOCK OFF

OFF: The tilt range is limited from 0 ° to 90 °.

ON: The digital flip function allows the tilt angle to widen up to 180 °. The image on the monitor screen is flipped horizontally and vertically at the tilt angle of approx. 135 ° (If the camera is installed on a ceiling).

Note: The tilt range narrows from 0 ° to 90 ° if PAN LIMIT is set to ON.

Notes:

Digital flip functions while moving the joystick downwards. In case of moving the joystick to other directions, it does not function.

When OFF is selected for DIGITAL FLIP, the following operations are required to move the camera 180 ° vertically.

1)Move the joystick downwards to aim the camera down.

2)Move the joystick to the right or left to rotate the camera 180 ° horizontally.

3)Move the joystick upwards.

To set the preset position directly from WV-CU360 System Controller, it is temporarily required to set both the electronic zoom function and digital flip function to OFF.

Tilt range setting is disabled between 90 ° and 185 °.

-25-

Image 25
Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Preface FeaturesDigital Flip Operation Camera Cleaning PrecautionsPreset Data Uploading or Down Loading Do not aim the camera at the same object for a long time ConsumablesSelf-diagnosis Function Prevention of blooming and smearConstruction Setup Menu SetupAUTO/ON/OFF P MON ESC CAM SET Preset IDWV-CU161C WV-RM70 Prog SWSetup Menu Description Camera Gain Control AGC Shutter Speed ShutterSynchronization Sync Important NoticesRS485 Communication Auto Focus AF Mode10Special 2 Menu SPECIAL2 11Self-diagnosis FunctionSetup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display Preset MenuPosition Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Scene File Setting Scene File Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Dwell Time Dwell TimePreset Speed Setting Preset Speed Deleting Preset PositionsTo Return to the Preset Number Set Menu To Return to the Setup MenuSelf Return Setting Self Home Position Setting HomeAuto Mode Selection Auto OFF SEQ Sort Auto PAN PatrolZoom →PUSH SET RET Digital Flip Setting Digital Flip Auto Pan Key Setting Auto PAN KEYSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialProportional Pan/Tilt PROPO. P/T Settings for on NeswArea Title Area Title Zoom ratioArea Title Editing Setting for on UserTo Quit Editing Patrol-learn and Patrol Play PatrolPatrol Learn with a Controller Having Patrol Key PAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White BalancePatrol Play with a Controller Having the Patrol Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller not Having the Patrol Key Patrol Play with the Auto PAN KeyElectronic Zoom EL-ZOOM Cleaning CleaningCNT-CLS 1, 2 Output Image Hold Image Hold Preset Alarm Preset ALMTilt Angle Tilt Angle 0 /5 To Display the Camera Setting Menu Camera SettingCamera Identification Camera ID ALC Mode with SUPER-D2 on Gain Control AGC on LOW/ MID/ HIGH/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAutomatic White Balance Control Mode AWC Auto-Tracing White Balance Mode ATW1/ ATW2White Balance White BAL Motion Detector Motion DET Resolution Resolution Auto Focus Setting AF ModeSpecial 2 Menu SPECIAL2 Auto S Auto M Auto L Manual L Manual M Manual SBW Setting Black and White Mode BW ModePIX Sens UP Setting Burst BW SettingCamera Resetting Camera Reset PIX OFF Setting PIX OFFTo Restore the Camera Default Position Refresh Reset to the Factory Default SettingsInitial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Menu Setting Factory Default SettingPreset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell Time CNT-CLS OFF Coax ALM OUTSetting the Switches InstallationPrecautions RS485 Parameter SetupUnit Number For Panasonic’s ProtocolUnit Assemble the Camera RS485 SettingSideway Cable Exit Hook the fall prevention wire on the camera mounting base How to Assemble the Cable with the Accessory Connector Accessory Connector InformationConnect this to 24 V AC Class 2 Power Supply only ConnectionsAlarm OUT Connections Alarm in ConnectionsRS485 Connection OUTSystem Connections WV-CS854B SpecificationsOptional Accessories AccessoriesWV-CS2SH Shortcuts AppendixImprimé au Japon