Samsung SCC-C6475(P) manual CC- C6475P Installatio n, Factory Default

Ad

Page 10

Factory Default

It recovers the whole setting of SCC-C6475(P) to the factory default. There are two Factory Default methods as follows.

(1) Using the Factory Default in the Reset page

Refer to 5. Setting and changing the function (System - Reset) in Chapter 3 Network menu Overview.

(2)Using the Factory Default button on the side of the unit. Proceed as follows.

1.Turn the power off.

2.While pressing the Factory default button, turn the power on.

3.When the Status LED flickers 3 times in red, unpress the Factory Default button.

4.If the Status LED turns to green, the whole setting of SCC- C6475(P) recovers to the factory default.

Caution

After executing, the user can access only when executing the basic network setting (IP Address, Subnet<RS-485 Half Duplex configuration> Mask, Gateway) by using the IP installer.

Chapter 2

SCC-C6475(P)Installation

In this chapter, we will check the contents of the package before installing the SCC-C6475(P), and prepare a power adapter suitable for the power supply system.

(Power Consumption: 25W; Voltage: AC24V, 1.5A)

Then, we will install the SCC-C6475(P) and connect the cables.

E

1-13

2-1

Image 10

Samsung SCC-C6475(P) manual CC- C6475P Installatio n, Factory Default

Contents SCC C6475P Important Safety Instructions FCC Statement Before Usage Table of contents Chapter CC-C6475 P Overvi ewSCC-C6475P Introduction Locations of ControlAdapter Connection SCC-C6475P Adapter BoardSetting communication Protocol Initial SettingSetting RS-422A/RS-485 termination Baud Rate SettingCC- C6475P Installatio n Factory DefaultBefore Installing Ceiling Mount Bracket SBR-100DCM Wall Mount Adaptor SADT-100WMCeiling Mount Adaptor SADT-100CM Indoor Housing SHG-120Outdoor Housing SHG-220 Pole Mount Adaptor SADT-100PMInstalling the Camera MatchCase of using xDSL/Cable Internet network and IP router Network Manual OverviewPage Http Port Case of connecting more than 2 cameras to one IP routerExample http//192.168.1.20181 Case of connecting more than 2 cameras to an IP router Case of using the LAN and IP router Example No.1 SCC-C6475P IP Subnet Mask Gateway Page RJ-45 Cross Lan Cable will be enclosed with products Example IP Subnet mask Gateway Page Setting the IP Case of connecting the camera in the intranet LANLog Title bar and the upper menuLogo and Video Format Viewer ScreenChoice of camera and channel Screen Size/Alarm/Banner window display Screencapture/record/playSetting the basic function Image screen adjustmentVideo Page User Camera PresetLanguage Setting the system StatusIP Filter LogSoftware Update ResetParameter LayoutOverlay Image Overlay Text Screen Look View Html CodeTransfer Setup AlarmAlarm Setup Alarm Priority SET PortNetwork NetworkIP Notification Setup Menu Overvie w Network Terms DefinitionStructure of the Setup Menu Exit QUIT/SAVESync Camera SET MenuCamera ID COLOR/BW Motion DETVideo SET Menu Motion ShutterAGC AGC GainWhite BAL DISSpecial PresetFocus Mode FocusZone SET Blank ALL below SET Zone Area Blank ALL AbovePryvacy Zone MAP Reverse SET ZoomZone DIR SET Zone AreaAuto SET Speed DirectionEndless PatternAlarm SET Other SET Short Keys System InfoInstallation of IP router SpecificationsConnecting the Internet LoginSetting the IP sharing setting Example Linksys model WRT54G Verify the Connection state Set the Time zonePort Forwarding Be sure to read this Setting the IP router Example Netgear model RP614v2 Access Setting the internet connectionVerify the connection status Setting IP router Example D-Link model DI-624+ Run WizardTime zone Password for RouterFirst screen Cable ModemEncryption Wireless LANRestart Checking the Connection Port Forwarding Be sure to readProduct specifications