Samsung SCC-C6475(P) manual Port, Alarm Priority SET

Page 40

●Active Time of Transfer

-Able to set the time limit for the alarm image transfer.

-In case of setting Always, image will be transferred whenever alarming.

-In case of setting Only Scheduled Time, image will be transferred only the defined date and time for the related alarm even when alarming.

●Schedule Transfer Setup

-Transfer the image at the date and time automatically when the user defines.

I/O Port

Consists of 4 Alarm inputs and 3 Alarm outputs and functions to execute connecting Preset or Pattern to detect the Alarm input from the external Sensor, and output the Alarm output signal from the outside. If the Alarm signal input lasts over 150 ms, it will be recognized as the Alarm signal. And the Alarm operation time depends on the Preset Dwell Time to each Alarm and the Pattern connection of it.

1. ALARM PRIORITY SET

Set the priority of the 4 Alarm inputs and react the Alarm input according to the priority.

Default priority is Alarm1: 1, Alarm2: 2, Alarm3: 3, Alarm4: 4

If alarming synchronously and setting the same priority, operates by the Default priority. While alarming, Motion is not detected.

2. ALARM IN SET

Set the input Type as “NO" (Normal Open), “NC" (Normal Close), “Off" according to the connected Sensor features.

3. ALARM OUT SET

Confront to one of the 3 Alarm outputs for each Alarm inputs

E

3-51

3-52

Image 40

Contents SCC C6475P Important Safety Instructions FCC Statement Before Usage Table of contents Chapter CC-C6475 P Overvi ewSCC-C6475P Introduction Locations of ControlAdapter Connection SCC-C6475P Adapter BoardInitial Setting Setting RS-422A/RS-485 terminationSetting communication Protocol Baud Rate SettingCC- C6475P Installatio n Factory DefaultBefore Installing Ceiling Mount Bracket SBR-100DCM Wall Mount Adaptor SADT-100WMIndoor Housing SHG-120 Outdoor Housing SHG-220Ceiling Mount Adaptor SADT-100CM Pole Mount Adaptor SADT-100PMInstalling the Camera MatchCase of using xDSL/Cable Internet network and IP router Network Manual OverviewPage Http Port Case of connecting more than 2 cameras to one IP routerExample http//192.168.1.20181 Case of connecting more than 2 cameras to an IP router Case of using the LAN and IP router Example No.1 SCC-C6475P IP Subnet Mask Gateway Page RJ-45 Cross Lan Cable will be enclosed with products Example IP Subnet mask Gateway Page Setting the IP Case of connecting the camera in the intranet LANLog Title bar and the upper menuLogo and Video Format Viewer ScreenChoice of camera and channel Screen Size/Alarm/Banner window display Screencapture/record/playSetting the basic function Image screen adjustmentVideo Page User Camera PresetLanguage Setting the system StatusIP Filter LogSoftware Update ResetParameter LayoutOverlay Image Overlay Text Screen Look View Html CodeTransfer Setup AlarmAlarm Setup Alarm Priority SET PortNetwork NetworkIP Notification Setup Menu Overvie w Network Terms DefinitionStructure of the Setup Menu Exit QUIT/SAVESync Camera SET MenuCamera ID COLOR/BW Motion DETVideo SET Menu Shutter AGCMotion AGC GainWhite BAL DISPreset Focus ModeSpecial FocusZone SET Blank ALL below SET Zone Area Blank ALL AbovePryvacy Zone MAP SET Zoom Zone DIR SETReverse Zone AreaAuto SET Direction EndlessSpeed PatternAlarm SET Other SET Short Keys System InfoInstallation of IP router SpecificationsConnecting the Internet LoginSetting the IP sharing setting Example Linksys model WRT54G Verify the Connection state Set the Time zonePort Forwarding Be sure to read this Setting the IP router Example Netgear model RP614v2 Access Setting the internet connectionVerify the connection status Setting IP router Example D-Link model DI-624+ Run WizardPassword for Router First screenTime zone Cable ModemEncryption Wireless LANRestart Checking the Connection Port Forwarding Be sure to readProduct specifications