Samsung SCC-C6475(P) manual Ceiling Mount Bracket SBR-100DCM, Wall Mount Adaptor SADT-100WM

Page 12

Cable Connection

1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT)

2. Then, connect the other end of the connector to the Video Input Terminal of the monitor.

3. Adjust the power select switch

(110 V or 220 V) after verifying the power to connect SCC- C6475(P).

4. Connect the two adapter power output cables to the power input terminal of SCC-C6475(P) by using the setting driver.

5. Connect the LAN cable to the IP router or hub to the using NETWORK connect terminal.

6.Connect the Remote Control Terminal of the

SCC-C6475(P)

and the external Controller.

Controller

Adapter BOARD

Installing SCC-C6475(P)

Installation Precautions

1)Make sure that the installation site can sufficiently support a minimum of four times the net weight of the SCC-C6475(P) IP SmartDome Camera and other accessories.

2)Install in an area where the space above the ceiling board is over 18 cm (7 in.) high.

3)Use the supplied screws to fasten the camera to the bracket assembly.

4)Keep persons away from the installation area, as there is a risk of falling objects.

Also, move valuables to a safe location before installation.

Separately Sold Products for Installation

Depending on the installation site, it may be convenient to use one of the following products.

1) CEILING MOUNT BRACKET (SBR-100DCM)

This bracket is used for installing the IP SmartDome Camera in the plenum above the drop ceiling.

2)WALL MOUNT ADAPTOR (SADT-100WM)

This adaptor is used for installing the indoor housing or the outdoor housing for the IP SmartDome Camera on a wall.

E

2-4

2-5

Image 12

Contents SCC C6475P Important Safety Instructions FCC Statement Before Usage Table of contents Chapter CC-C6475 P Overvi ewSCC-C6475P Introduction Locations of ControlAdapter Connection SCC-C6475P Adapter BoardInitial Setting Setting RS-422A/RS-485 terminationSetting communication Protocol Baud Rate SettingCC- C6475P Installatio n Factory DefaultBefore Installing Ceiling Mount Bracket SBR-100DCM Wall Mount Adaptor SADT-100WMIndoor Housing SHG-120 Outdoor Housing SHG-220Ceiling Mount Adaptor SADT-100CM Pole Mount Adaptor SADT-100PMInstalling the Camera MatchCase of using xDSL/Cable Internet network and IP router Network Manual OverviewPage Case of connecting more than 2 cameras to one IP router Http PortExample http//192.168.1.20181 Case of connecting more than 2 cameras to an IP router Case of using the LAN and IP router Example No.1 SCC-C6475P IP Subnet Mask Gateway Page RJ-45 Cross Lan Cable will be enclosed with products Example IP Subnet mask Gateway Page Setting the IP Case of connecting the camera in the intranet LANLog Title bar and the upper menuViewer Screen Logo and Video FormatChoice of camera and channel Screen Size/Alarm/Banner window display Screencapture/record/playImage screen adjustment Setting the basic functionVideo Page User Preset CameraLanguage Setting the system StatusIP Filter LogSoftware Update ResetLayout ParameterOverlay Image Overlay Text Screen Look View Html CodeAlarm Transfer SetupAlarm Setup Alarm Priority SET PortNetwork NetworkIP Notification Setup Menu Overvie w Network Terms DefinitionStructure of the Setup Menu Exit QUIT/SAVECamera SET Menu SyncCamera ID COLOR/BW Motion DETVideo SET Menu Shutter AGCMotion AGC GainWhite BAL DISPreset Focus ModeSpecial FocusZone SET Blank ALL Above Blank ALL below SET Zone AreaPryvacy Zone MAP SET Zoom Zone DIR SETReverse Zone AreaAuto SET Direction EndlessSpeed PatternAlarm SET Other SET Short Keys System InfoInstallation of IP router SpecificationsLogin Connecting the InternetSetting the IP sharing setting Example Linksys model WRT54G Set the Time zone Verify the Connection statePort Forwarding Be sure to read this Setting the IP router Example Netgear model RP614v2 Access Setting the internet connectionVerify the connection status Setting IP router Example D-Link model DI-624+ Run WizardPassword for Router First screenTime zone Cable ModemWireless LAN EncryptionRestart Checking the Connection Port Forwarding Be sure to readProduct specifications