Samsung SCC-C6475(P) manual Checking the Connection, Port Forwarding Be sure to read

Page 67

10. Checking the Connection

This step is for checking the connection status.

1.Select “Status”.

2.Select “Device Info.”.

3.Check the information of WAN part. If Disconnected, press the “Connect” button and retry to access. If it is unable to keep connecting, retry to go back at first (access).

4.Be sure to remember the Subnet Mask number to set SCC-C6475(P) afterwards.

11.Port Forwarding (Be sure to read.)

1.Select “Advanced” of Virtual Server.

Set in order Virtual Server (Port Forwarding) about HTTP/TCP/UDP.

2.Virtual Server (Port Forwarding) for HTTP

Enabled : Select

Name : Enter HTTP

Private IP : 192.168.0.2 ~ 255(Except the IP assigned to the connected internet equipment)

Protocol Type : Select “TCP”

Private Port and Public Port : Enter “80”

Schedule : Select “Always”

Press the “Apply” button.

3.Virtual Server (Port Forwarding) for TCP

Enabled : Select

Name : Enter “TCP”.

Private IP : Enter the same IP with HTTP.

Protocol Type : Select “TCP”.

Private Port and Public Port : Enter 554/554, 555/555, 556/556.

Schedule : Select “Always”.

Press Apply button.

4.Virtual Server (Port Forwarding) for UDP

Enabled : Select

Name : Enter “UDP”.

Private IP : Enter the same IP with HTTP/TCP.

Protocol Type : Select “UDP”.

Private Port and Public Port : Enter 8000/8000 ~ 8009/8009.

Schedule : Select “Always”.

Press the “Apply” button.

Note Be sure to memorize the above set items to use to set SCC-C6475(P).

5. Close the internet explorer window.

E

5-16

5-17

Image 67
Contents SCC C6475P Important Safety Instructions FCC Statement Before Usage Table of contents CC-C6475 P Overvi ew ChapterLocations of Control SCC-C6475P IntroductionSCC-C6475P Adapter Board Adapter ConnectionBaud Rate Setting Initial SettingSetting RS-422A/RS-485 termination Setting communication ProtocolFactory Default CC- C6475P Installatio nBefore Installing Wall Mount Adaptor SADT-100WM Ceiling Mount Bracket SBR-100DCMPole Mount Adaptor SADT-100PM Indoor Housing SHG-120Outdoor Housing SHG-220 Ceiling Mount Adaptor SADT-100CMMatch Installing the CameraNetwork Manual Overview Case of using xDSL/Cable Internet network and IP routerPage Http Port Case of connecting more than 2 cameras to one IP routerExample http//192.168.1.20181 Case of connecting more than 2 cameras to an IP router Case of using the LAN and IP router Example No.1 SCC-C6475P IP Subnet Mask Gateway Page RJ-45 Cross Lan Cable will be enclosed with products Example IP Subnet mask Gateway Page Case of connecting the camera in the intranet LAN Setting the IPTitle bar and the upper menu LogLogo and Video Format Viewer ScreenChoice of camera and channel Screencapture/record/play Screen Size/Alarm/Banner window displaySetting the basic function Image screen adjustmentVideo Page User Camera PresetLanguage Status Setting the systemLog IP FilterReset Software UpdateParameter LayoutOverlay Image Overlay Text View Html Code Screen LookTransfer Setup AlarmAlarm Setup Port Alarm Priority SETNetwork NetworkIP Notification Network Terms Definition Setup Menu Overvie wExit QUIT/SAVE Structure of the Setup MenuSync Camera SET MenuCamera ID Motion DET COLOR/BWVideo SET Menu AGC Gain ShutterAGC MotionDIS White BALFocus PresetFocus Mode SpecialZone SET Blank ALL below SET Zone Area Blank ALL AbovePryvacy Zone MAP Zone Area SET ZoomZone DIR SET ReverseAuto SET Pattern DirectionEndless SpeedAlarm SET Other SET System Info Short KeysSpecifications Installation of IP routerConnecting the Internet LoginSetting the IP sharing setting Example Linksys model WRT54G Verify the Connection state Set the Time zonePort Forwarding Be sure to read this Setting the internet connection Setting the IP router Example Netgear model RP614v2 AccessVerify the connection status Run Wizard Setting IP router Example D-Link model DI-624+Cable Modem Password for RouterFirst screen Time zoneEncryption Wireless LANRestart Port Forwarding Be sure to read Checking the ConnectionProduct specifications