Icom IC-R3 instruction manual Dual LCD

Page 10

2 PANEL DESCRIPTION

■Dual LCD

The receiver has dual LCDs for versatile display selection.

The color LCD has 5 screens and 1 optional screen as fol- lows:

simple, multi-function, band scope, direction ﬁnding, TV (fre- quency selection) and amateur TV* screen.

* Amateur TV screen can be selected for the ATV-type and 1200/2400 MHz bands only.

The color LCD can be used when the operating frequency is 30 MHz and above.

qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired.

wPush [FUNC] + [↕] momentarily one or more times to tog- gle the screen of the color LCD.

While the color LCD is in use, the sub LCD displays the voltage of the power source.

RX

Appears when simple screen is selected.

FM

PSKIP

FM

PSKIP

146.100.000

TS

146.100.000

TS

15.0

15.0

RX

S1

3

5

7 9

Simple screen

VOL

Multi-function

screen

FUNC

FM

PSKIP

+

146.100.000

TS

15.0

momentarily

ATV screen (p. 36;

Direction finding

ATV type, 1200/2400 MHz bands only)

screen (p. 37)

FM

PSKIP

146.100.000

TS= 15.0

S1 3

5

7 9

SWEEP- 10K

RX

VOL

TV screen (p. 34;	Band scope
frequency selection)	screen (p. 33)

6

Image 10

Contents IR3 Even when the receiver power is OFF, a slight current still You experience a ringing in your ears, reduce the volumeAreas with temperatures below -10C +14F or above +60C +140FSupplied Accessories Accessories included with the receiver QtyTable of Contents Antenna Accessory AttachmentBattery installation Belt clipPanel Description Panel descriptionMonitor Switch SQL ATT VFO/MEMORY Switch V/M SkipMode Switch Mode SET External DC Power Jack DCFunction display 2ATTENUATOR Indicator p Skip Scan Indicator pgsBattery Indicators Audio and video output jack informationDual LCD VFO and memory channels Frequency and Channel SettingWhat is VFO? Operating band selectionSetting a frequency Setting a tuning stepAttenuator function Push SQL ATT to exit the attenuator setting conditionSelecting a memory channel Lock functionReceiving When a signal is receivedBasic Operation U.S.A. version automatically turns itself OFF whenWhile pushing SQL, rotate Setting volume levelSetting squelch level Dial to select the squelch levelReceive mode selection Monitor functionDisplay backlighting Setting the backlighting conditionPush Func + Mode SET momentarily to enter set mode Rotate Dial until Light appearsGeneral Memory channel contentsMemory Channels Programming during selectionTransferring memory contents to another memory Programming after selectionPush Func + V/M for 2 sec. to clear Memory bank selection Memory clearExample Clearing memory channel 3 memory bank a Rotate the tuning dial to select the desired character Memory namesFull Scan p Scan OperationScan types Function pFull/band/programmed scan Release ↔ to start the scanMemory bank scan To stop the scan, push ↔ againSelecting scan edges Band rangesScan resume condition Skip channel settingSetting the scan pause time Rotate Dial until Pause Scan or Pause appearsSetting the scan resume time Rotate Dial until Scan Resume or RESUmE appearsProgramming a skip frequency Frequency skip functionFrequency skip function ON/OFF Memory Scan Watch p Priority WatchPriority watch types VFO Scan Watch pMemory channel watch and memory scan Watch Push Mode SET to exit set mode and start the watchPriority watch operation Rotate Dial to select Priority or PRIoVFO scan watch Tone squelch operation Setting subaudible tones for tone squelch OperationSubaudible Tone Operation OperationRotate Dial until Tone Freq. or tonE appears Pocket beep operationAvailable subaudible tone frequencies Unit Hz Push SQL to stop the beeps and ﬂashing Tone scanPush ↔ to stop the scan Duplex shift direction Duplex OperationRotate Dial until Duplex or dUP appears Offset frequency Rotate Dial until Offset Freq. or oFFSEt appearsBand Scope Range, if desiredTV operation Skip channel settingTV Operation TV channel receivingPush ↔ one or more times to select the band above 30 MHz TV frequency AM TV receivingTV frequency AM TV memory channel Push Func + one or more times to select the TV screenATV operation Sub carrier adjustmentATV memory channel Direction Finding Signal sourceSignal levels Direction ﬁnding function exampleSet mode items Set modeOther Functions Dial select step Setting dial select stepRelease Func to exit the condition Beep tones Auto power-off functionRotate Dial until A.Power OFF or AP oFF appears Rotate Dial until Beep Audio or bEEP appearsRotate Dial until Power Save or P Save appears Power saverMonitor switch action Rotate Dial until Monitor or monI appearsRotate Dial until Dial Speedup or SPEEd appears Dial speed accelerationLock function effect Rotate Dial until Key Lock or LoCk appearsDisplay contrast Display mode selectionColor LCD can be automatically turned on when using Rotate Dial until Display or dISP appearsDisplay background color Display brightnessRotate Dial until Bright appears Push Power for 2 sec. to turn power OFF Partial resetTotal reset Cloning functionBattery charging Battery ChargingBattery cautions Battery pack installationRegular charging CP-18A/E fuse ReplacementCP-18A/ETurn power OFF Check Rapid charging with the BC-135Operation Flow Chart Memory mode VFO modeAuto power OFF p Confirmation beep p Backlighting p Power save pScan resume time p A. channels TV Frequency TableCcir channels Taiwan channels Australian channelsNew Zealand channels China channels Indonesian channelsItalian channels FOT channels General Specifications and OptionsReceiver Operating periods Approx OptionsTroubleshooting Problem Possible Cause SolutionQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan