Icom IC-R3 instruction manual Memory bank scan, To stop the scan, push ↔ again

Page 24

6 SCAN OPERATION

■Memory (bank) scan

qSelect memory mode with [V/M].

wFor memory bank scan, rotate [DIAL] while pushing [FUNC] to select the desired memory bank.

eMake sure the squelch is set to the threshold point.

•Select automatic squelch (AUTO) or a level (1–9) where the noise is just muted. (p. 11)

rPush and hold [↔], then rotate [DIAL] to turn the memory bank scan ON or OFF.

•“ALL” indicates all memory banks are scanned (memory bank scan OFF); “BANK” indicates the selected memory bank is scanned (memory bank scan ON).

FM			PSKIP	FM				PSKIP
			M:A00				M:A00
146.100.000				146.100.000
TS		15.0		TS		15.0
BANK				ALL
S1	3		7 9	S1	3		7	9
S1	3	5	7 9	S1	3	5	7	9
VOL				VOL
VOL				VOL

Bank scan ON

Bank scan OFF

tRelease [↔] to start the scan.

•Decimal point(s) ﬂashes while scanning.

•To change the scanning direction, rotate [DIAL].

•If the pocket beep function is activated, the receiver automati- cally selects the tone squelch function when a scan starts.

yTo stop the scan, push [↔] again.

Image 24

Contents IR3 You experience a ringing in your ears, reduce the volume Areas with temperatures below -10C +14F or aboveEven when the receiver power is OFF, a slight current still +60C +140FSupplied Accessories Accessories included with the receiver QtyTable of Contents Accessory Attachment Battery installationAntenna Belt clipPanel Description Panel descriptionVFO/MEMORY Switch V/M Skip Mode Switch Mode SETMonitor Switch SQL ATT External DC Power Jack DCFunction display Skip Scan Indicator pgs Battery Indicators2ATTENUATOR Indicator p Audio and video output jack informationDual LCD Frequency and Channel Setting What is VFO?VFO and memory channels Operating band selectionSetting a frequency Setting a tuning stepPush SQL ATT to exit the attenuator setting condition Selecting a memory channelAttenuator function Lock functionWhen a signal is received Basic OperationReceiving U.S.A. version automatically turns itself OFF whenSetting volume level Setting squelch levelWhile pushing SQL, rotate Dial to select the squelch levelReceive mode selection Monitor functionSetting the backlighting condition Push Func + Mode SET momentarily to enter set modeDisplay backlighting Rotate Dial until Light appearsMemory channel contents Memory ChannelsGeneral Programming during selectionTransferring memory contents to another memory Programming after selectionMemory bank selection Memory clear Push Func + V/M for 2 sec. to clearExample Clearing memory channel 3 memory bank a Rotate the tuning dial to select the desired character Memory namesScan Operation Scan typesFull Scan p Function pFull/band/programmed scan Release ↔ to start the scanMemory bank scan To stop the scan, push ↔ againSelecting scan edges Band rangesSkip channel setting Setting the scan pause timeScan resume condition Rotate Dial until Pause Scan or Pause appearsSetting the scan resume time Rotate Dial until Scan Resume or RESUmE appearsFrequency skip function Programming a skip frequencyFrequency skip function ON/OFF Priority Watch Priority watch typesMemory Scan Watch p VFO Scan Watch pPush Mode SET to exit set mode and start the watch Priority watch operationMemory channel watch and memory scan Watch Rotate Dial to select Priority or PRIoVFO scan watch Setting subaudible tones for tone squelch Operation Subaudible Tone OperationTone squelch operation OperationPocket beep operation Rotate Dial until Tone Freq. or tonE appearsAvailable subaudible tone frequencies Unit Hz Tone scan Push SQL to stop the beeps and ﬂashingPush ↔ to stop the scan Duplex Operation Duplex shift directionRotate Dial until Duplex or dUP appears Offset frequency Rotate Dial until Offset Freq. or oFFSEt appearsBand Scope Range, if desiredSkip channel setting TV OperationTV operation TV channel receivingTV frequency AM TV receiving TV frequency AM TV memory channelPush ↔ one or more times to select the band above 30 MHz Push Func + one or more times to select the TV screenSub carrier adjustment ATV operationATV memory channel Signal source Signal levelsDirection Finding Direction ﬁnding function exampleSet mode Set mode itemsOther Functions Setting dial select step Dial select stepRelease Func to exit the condition Auto power-off function Rotate Dial until A.Power OFF or AP oFF appearsBeep tones Rotate Dial until Beep Audio or bEEP appearsPower saver Monitor switch actionRotate Dial until Power Save or P Save appears Rotate Dial until Monitor or monI appearsDial speed acceleration Lock function effectRotate Dial until Dial Speedup or SPEEd appears Rotate Dial until Key Lock or LoCk appearsDisplay mode selection Color LCD can be automatically turned on when usingDisplay contrast Rotate Dial until Display or dISP appearsDisplay brightness Display background colorRotate Dial until Bright appears Partial reset Total resetPush Power for 2 sec. to turn power OFF Cloning functionBattery Charging Battery cautionsBattery charging Battery pack installationCP-18A/E fuse ReplacementCP-18A/E Turn power OFF CheckRegular charging Rapid charging with the BC-135Operation Flow Chart Memory mode VFO modeConfirmation beep p Backlighting p Power save p Auto power OFF pScan resume time p TV Frequency Table A. channelsCcir channels Australian channels Taiwan channelsNew Zealand channels China channels Indonesian channelsItalian channels FOT channels Specifications and Options GeneralReceiver Operating periods Approx OptionsTroubleshooting Problem Possible Cause SolutionQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan