Icom IC-R3 instruction manual Declaration of Conformity

Page 63

DECLARATION OF CONFORMITY

We Icom Inc. Japan

6-9-16, Kamihigashi, Hirano-ku

Osaka 547-0002, Japan

Declare on our sole responsability that this equipment complies the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/CE.

Kind of equipment: COMMUNICATIONS RECEIVER

Type-designation: iC-r3

Version (where applicable):

This compliances is based on conformity with the following harmonised standards, specifications or documents:

i)EN 60950

ii)prEN 301 489-1

iii)prEN 301 489-15

iv)prEN 301 783-2

Düsseldorf 11. July. 2000

Place and date of issue

Icom (Europe) GmbH

Himmelgeister straße 100 D-40225 Düsseldorf

Authorized representative name

Icom (Europe) GmbH

T. Aoki

General Manager

Signature

Image 63 Icom IC-R3 instruction manual Declaration of Conformity
Contents IR3 +60C +140F You experience a ringing in your ears, reduce the volumeAreas with temperatures below -10C +14F or above Even when the receiver power is OFF, a slight current stillAccessories included with the receiver Qty Supplied AccessoriesTable of Contents Belt clip Accessory AttachmentBattery installation AntennaPanel description Panel DescriptionExternal DC Power Jack DC VFO/MEMORY Switch V/M SkipMode Switch Mode SET Monitor Switch SQL ATTFunction display Audio and video output jack information Skip Scan Indicator pgsBattery Indicators 2ATTENUATOR Indicator pDual LCD Operating band selection Frequency and Channel SettingWhat is VFO? VFO and memory channelsSetting a tuning step Setting a frequencyLock function Push SQL ATT to exit the attenuator setting conditionSelecting a memory channel Attenuator functionU.S.A. version automatically turns itself OFF when When a signal is receivedBasic Operation ReceivingDial to select the squelch level Setting volume levelSetting squelch level While pushing SQL, rotateMonitor function Receive mode selectionRotate Dial until Light appears Setting the backlighting conditionPush Func + Mode SET momentarily to enter set mode Display backlightingProgramming during selection Memory channel contentsMemory Channels GeneralProgramming after selection Transferring memory contents to another memoryMemory bank selection Memory clear Push Func + V/M for 2 sec. to clearExample Clearing memory channel 3 memory bank a Memory names Rotate the tuning dial to select the desired characterFunction p Scan OperationScan types Full Scan pRelease ↔ to start the scan Full/band/programmed scanTo stop the scan, push ↔ again Memory bank scanBand ranges Selecting scan edgesRotate Dial until Pause Scan or Pause appears Skip channel settingSetting the scan pause time Scan resume conditionRotate Dial until Scan Resume or RESUmE appears Setting the scan resume timeFrequency skip function Programming a skip frequencyFrequency skip function ON/OFF VFO Scan Watch p Priority WatchPriority watch types Memory Scan Watch pRotate Dial to select Priority or PRIo Push Mode SET to exit set mode and start the watchPriority watch operation Memory channel watch and memory scan WatchVFO scan watch Operation Setting subaudible tones for tone squelch OperationSubaudible Tone Operation Tone squelch operationPocket beep operation Rotate Dial until Tone Freq. or tonE appearsAvailable subaudible tone frequencies Unit Hz Tone scan Push SQL to stop the beeps and flashingPush ↔ to stop the scan Duplex Operation Duplex shift directionRotate Dial until Duplex or dUP appears Rotate Dial until Offset Freq. or oFFSEt appears Offset frequencyRange, if desired Band ScopeTV channel receiving Skip channel settingTV Operation TV operationPush Func + one or more times to select the TV screen TV frequency AM TV receivingTV frequency AM TV memory channel Push ↔ one or more times to select the band above 30 MHzSub carrier adjustment ATV operationATV memory channel Direction finding function example Signal sourceSignal levels Direction FindingSet mode Set mode itemsOther Functions Setting dial select step Dial select stepRelease Func to exit the condition Rotate Dial until Beep Audio or bEEP appears Auto power-off functionRotate Dial until A.Power OFF or AP oFF appears Beep tonesRotate Dial until Monitor or monI appears Power saverMonitor switch action Rotate Dial until Power Save or P Save appearsRotate Dial until Key Lock or LoCk appears Dial speed accelerationLock function effect Rotate Dial until Dial Speedup or SPEEd appearsRotate Dial until Display or dISP appears Display mode selectionColor LCD can be automatically turned on when using Display contrastDisplay brightness Display background colorRotate Dial until Bright appears Cloning function Partial resetTotal reset Push Power for 2 sec. to turn power OFFBattery pack installation Battery ChargingBattery cautions Battery chargingRapid charging with the BC-135 CP-18A/E fuse ReplacementCP-18A/ETurn power OFF Check Regular chargingMemory mode VFO mode Operation Flow ChartConfirmation beep p Backlighting p Power save p Auto power OFF pScan resume time p TV Frequency Table A. channelsCcir channels Australian channels Taiwan channelsNew Zealand channels Indonesian channels China channelsItalian channels FOT channels Specifications and Options GeneralReceiver Options Operating periods ApproxProblem Possible Cause Solution TroubleshootingQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan