Icom IC-R3 instruction manual TV frequency AM TV receiving, TV frequency AM TV memory channel

Page 39

◊TV frequency (AM TV) receiving

You can set the TV frequency instead of channel selection, if desired.

qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired.

•The audio part of the TV contents can be received when the color LCD is turned OFF.

wPush [↔] one or more times to select the band above 30 MHz.

• TV receiving does not function for less than 30 MHz.

ePush [FUNC] + [↕] one or more times to select the TV screen.

•“tV” and frequency appear in the sub LCD.

•The squelch is automatically opened. Push [SQL] to toggle be- tween squelch open and audio mute conditions.

rRotate [DIAL] to set the desired frequency.

•Push [↔] one or more times to select the band.

•Rotate [DIAL] while pushing [FUNC] for dial select step. (p. 39)

WFM

RX

TV OPERATION 11

◊TV frequency (AM TV) memory channel

The receiver has 10 memory channels for storage of often- used TV (AM TV) frequencies.

qSet the desired frequency with [DIAL].

•Push [↔] one or more times to select the band.

•Rotate [DIAL] while pushing [FUNC] for dial select step. (p. 39) w Push [V/M] for 1 sec. to indicate memory channels.

•Do not hold [V/M] for more than 2 sec., otherwise the previously selected memory channel will be overwritten.

eRotate [DIAL] to select the desired channel. r Push [V/M] for 1 sec. to program.

•Keep pushing for 2 sec. or more to automatically select the next memory channel, if desired.

WFM

RX

Memory programming after selection, memory transferring

or memory clearing can be used as same manner of regu- lar memory channels. (pgs. 15, 16)

35

Image 39

Contents IR3 +60C +140F You experience a ringing in your ears, reduce the volumeAreas with temperatures below -10C +14F or above Even when the receiver power is OFF, a slight current stillAccessories included with the receiver Qty Supplied AccessoriesTable of Contents Belt clip Accessory AttachmentBattery installation AntennaPanel description Panel DescriptionExternal DC Power Jack DC VFO/MEMORY Switch V/M SkipMode Switch Mode SET Monitor Switch SQL ATTFunction display Audio and video output jack information Skip Scan Indicator pgsBattery Indicators 2ATTENUATOR Indicator pDual LCD Operating band selection Frequency and Channel SettingWhat is VFO? VFO and memory channelsSetting a tuning step Setting a frequencyLock function Push SQL ATT to exit the attenuator setting conditionSelecting a memory channel Attenuator functionU.S.A. version automatically turns itself OFF when When a signal is receivedBasic Operation ReceivingDial to select the squelch level Setting volume levelSetting squelch level While pushing SQL, rotateMonitor function Receive mode selectionRotate Dial until Light appears Setting the backlighting conditionPush Func + Mode SET momentarily to enter set mode Display backlightingProgramming during selection Memory channel contentsMemory Channels GeneralProgramming after selection Transferring memory contents to another memoryMemory bank selection Memory clear Push Func + V/M for 2 sec. to clearExample Clearing memory channel 3 memory bank a Memory names Rotate the tuning dial to select the desired characterFunction p Scan OperationScan types Full Scan pRelease ↔ to start the scan Full/band/programmed scanTo stop the scan, push ↔ again Memory bank scanBand ranges Selecting scan edgesRotate Dial until Pause Scan or Pause appears Skip channel settingSetting the scan pause time Scan resume conditionRotate Dial until Scan Resume or RESUmE appears Setting the scan resume timeFrequency skip function Programming a skip frequencyFrequency skip function ON/OFF VFO Scan Watch p Priority WatchPriority watch types Memory Scan Watch pRotate Dial to select Priority or PRIo Push Mode SET to exit set mode and start the watchPriority watch operation Memory channel watch and memory scan WatchVFO scan watch Operation Setting subaudible tones for tone squelch OperationSubaudible Tone Operation Tone squelch operationPocket beep operation Rotate Dial until Tone Freq. or tonE appearsAvailable subaudible tone frequencies Unit Hz Tone scan Push SQL to stop the beeps and ﬂashingPush ↔ to stop the scan Duplex Operation Duplex shift directionRotate Dial until Duplex or dUP appears Rotate Dial until Offset Freq. or oFFSEt appears Offset frequencyRange, if desired Band ScopeTV channel receiving Skip channel settingTV Operation TV operationPush Func + one or more times to select the TV screen TV frequency AM TV receivingTV frequency AM TV memory channel Push ↔ one or more times to select the band above 30 MHzSub carrier adjustment ATV operationATV memory channel Direction ﬁnding function example Signal sourceSignal levels Direction FindingSet mode Set mode itemsOther Functions Setting dial select step Dial select stepRelease Func to exit the condition Rotate Dial until Beep Audio or bEEP appears Auto power-off functionRotate Dial until A.Power OFF or AP oFF appears Beep tonesRotate Dial until Monitor or monI appears Power saverMonitor switch action Rotate Dial until Power Save or P Save appearsRotate Dial until Key Lock or LoCk appears Dial speed accelerationLock function effect Rotate Dial until Dial Speedup or SPEEd appearsRotate Dial until Display or dISP appears Display mode selectionColor LCD can be automatically turned on when using Display contrastDisplay brightness Display background colorRotate Dial until Bright appears Cloning function Partial resetTotal reset Push Power for 2 sec. to turn power OFFBattery pack installation Battery ChargingBattery cautions Battery chargingRapid charging with the BC-135 CP-18A/E fuse ReplacementCP-18A/ETurn power OFF Check Regular chargingMemory mode VFO mode Operation Flow ChartConfirmation beep p Backlighting p Power save p Auto power OFF pScan resume time p TV Frequency Table A. channelsCcir channels Australian channels Taiwan channelsNew Zealand channels Indonesian channels China channelsItalian channels FOT channels Specifications and Options GeneralReceiver Options Operating periods ApproxProblem Possible Cause Solution TroubleshootingQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan