Icom IC-R3 instruction manual Function display

Page 8

2 PANEL DESCRIPTION

■Function display

q w e r

AM WFM DUP TSQL PRIO

	75	t
	50	t
	50
!2	25

!1	RX ATT		P					y
								y


!0			o i u

q RECEIVE MODE INDICATORS (p. 12)

Show the receive mode.

•AM, FM and WFM are available.

w DUPLEX INDICATORS (p. 31)

Appear when semi-duplex operation (repeater operation) is in use.

•“– DUP” appears when minus duplex is selected; “DUP” only, ap- pears when plus duplex is selected.

e TONE INDICATORS (p. 28)

➥“TSQL” appears when the tone squelch function is acti- vated and “TSQL ë” appears during pocket beep oper- ation.

➥“ë” flashes when the correct tone is received during pocket beep operation.

r PRIORITY WATCH INDICATOR (p. 25) Appears when priority watch is in use.

t FREQUENCY READOUT

Shows the operating frequency, set mode contents, etc.

•The smaller “75,” “50” and “25” to the right of the readout indi- cate 7.5, 5.0 and 2.5 kHz, respectively.

•The decimal point of the frequency ﬂashes during scan.

y MEMORY CHANNEL READOUT (p. 7)

Shows the memory channel number, 8 memory banks (A–H), etc.

•The 1st digit (A–H) of regular memory indicates memory bank.

•‘tV0’ to ‘tV9’ indicate AM TV memory channels. (p. 35)

•‘t00’ to ‘t49’ indicate FM TV memory channels. (p. 36)

•Sufﬁx ‘A’ and ‘b’ indicate scan edge memory channels.

u MEMORY MODE INDICATOR (p. 7)

Appears when a memory channel is selected.

4

Image 8

Contents IR3 You experience a ringing in your ears, reduce the volume Areas with temperatures below -10C +14F or aboveEven when the receiver power is OFF, a slight current still +60C +140FSupplied Accessories Accessories included with the receiver QtyTable of Contents Accessory Attachment Battery installationAntenna Belt clipPanel Description Panel descriptionVFO/MEMORY Switch V/M Skip Mode Switch Mode SETMonitor Switch SQL ATT External DC Power Jack DCFunction display Skip Scan Indicator pgs Battery Indicators2ATTENUATOR Indicator p Audio and video output jack informationDual LCD Frequency and Channel Setting What is VFO?VFO and memory channels Operating band selectionSetting a frequency Setting a tuning stepPush SQL ATT to exit the attenuator setting condition Selecting a memory channelAttenuator function Lock functionWhen a signal is received Basic OperationReceiving U.S.A. version automatically turns itself OFF whenSetting volume level Setting squelch levelWhile pushing SQL, rotate Dial to select the squelch levelReceive mode selection Monitor functionSetting the backlighting condition Push Func + Mode SET momentarily to enter set modeDisplay backlighting Rotate Dial until Light appearsMemory channel contents Memory ChannelsGeneral Programming during selectionTransferring memory contents to another memory Programming after selectionExample Clearing memory channel 3 memory bank a Memory bank selection Memory clearPush Func + V/M for 2 sec. to clear Rotate the tuning dial to select the desired character Memory namesScan Operation Scan typesFull Scan p Function pFull/band/programmed scan Release ↔ to start the scanMemory bank scan To stop the scan, push ↔ againSelecting scan edges Band rangesSkip channel setting Setting the scan pause timeScan resume condition Rotate Dial until Pause Scan or Pause appearsSetting the scan resume time Rotate Dial until Scan Resume or RESUmE appearsFrequency skip function ON/OFF Frequency skip functionProgramming a skip frequency Priority Watch Priority watch typesMemory Scan Watch p VFO Scan Watch pPush Mode SET to exit set mode and start the watch Priority watch operationMemory channel watch and memory scan Watch Rotate Dial to select Priority or PRIoVFO scan watch Setting subaudible tones for tone squelch Operation Subaudible Tone OperationTone squelch operation OperationAvailable subaudible tone frequencies Unit Hz Pocket beep operationRotate Dial until Tone Freq. or tonE appears Push ↔ to stop the scan Tone scanPush SQL to stop the beeps and ﬂashing Rotate Dial until Duplex or dUP appears Duplex OperationDuplex shift direction Offset frequency Rotate Dial until Offset Freq. or oFFSEt appearsBand Scope Range, if desiredSkip channel setting TV OperationTV operation TV channel receivingTV frequency AM TV receiving TV frequency AM TV memory channelPush ↔ one or more times to select the band above 30 MHz Push Func + one or more times to select the TV screenATV memory channel Sub carrier adjustmentATV operation Signal source Signal levelsDirection Finding Direction ﬁnding function exampleOther Functions Set modeSet mode items Release Func to exit the condition Setting dial select stepDial select step Auto power-off function Rotate Dial until A.Power OFF or AP oFF appearsBeep tones Rotate Dial until Beep Audio or bEEP appearsPower saver Monitor switch actionRotate Dial until Power Save or P Save appears Rotate Dial until Monitor or monI appearsDial speed acceleration Lock function effectRotate Dial until Dial Speedup or SPEEd appears Rotate Dial until Key Lock or LoCk appearsDisplay mode selection Color LCD can be automatically turned on when usingDisplay contrast Rotate Dial until Display or dISP appearsRotate Dial until Bright appears Display brightnessDisplay background color Partial reset Total resetPush Power for 2 sec. to turn power OFF Cloning functionBattery Charging Battery cautionsBattery charging Battery pack installationCP-18A/E fuse ReplacementCP-18A/E Turn power OFF CheckRegular charging Rapid charging with the BC-135Operation Flow Chart Memory mode VFO modeScan resume time p Confirmation beep p Backlighting p Power save pAuto power OFF p Ccir channels TV Frequency TableA. channels New Zealand channels Australian channelsTaiwan channels China channels Indonesian channelsItalian channels FOT channels Receiver Specifications and OptionsGeneral Operating periods Approx OptionsTroubleshooting Problem Possible Cause SolutionQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan