Icom IC-R3 instruction manual Quick Reference

Page 61

57

OPERATING GUIDE

iR3

BASIC OPERATION

qPush [POWER] for 2 sec.

wPush [] to set the desired audio level.

eSelect VFO mode with [V/M].

r Select the desired band with []. t Rotate [DIAL] to change the fre-

quency.

The frequency changes according to the preset tuning steps.

ySet the squelch level.

While pushing [SQL], rotate [DIAL].

The first click of [DIAL] indicates the current squelch level.

•“LEVEL1” is loose squelch and “LEVEL9” is tight squelch.

q Cut

w Folde Complete

<CUT HERE>

•“AUTO” indicates automatic level ad- justment.

tWhen a signal is received:

Squelch opens and audio is emitted from the speaker.

The S/RF indicator shows the relative signal strength.

Using the dial select step (p. 39) Rotate [DIAL] while pushing [FUNC] to change the frequency in 100 kHz, 1 MHz or 10 MHz steps.

DUPLEX OPERATION

qSet the receive station frequency

(e.g. repeater output frequency).

wSet the shift direction of the trans- mit station frequency in set mode. (–DUP or DUP)

e Push and hold [SQL] to monitor the transmit station’s frequency.

By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc.

Important operating instructions are summed up in this and the following page for your simple reference.

QUICK REFERENCE 19

 

 

 

 

 

 

 

Tone scan (p. 30)

Push [FUNC] + [] for 2 sec. to start the tone scan.

MEMORY CHANNEL SELECTION

qPush [V/M] to select memory

mode.

“M:” or “X” appears.

wSelect a memory channel with [DIAL].

eRotate [DIAL] while pushing [FUNC] to select the memory bank.

MEMORY CLEAR

qSelect the desired memory chan- nel.

wSelect VFO mode with [V/M] and push [V/M] for 1 sec. to indicate the channel.

ePush [FUNC] + [V/M] for 2 sec.

Image 61
Contents IR3 Areas with temperatures below -10C +14F or above You experience a ringing in your ears, reduce the volumeEven when the receiver power is OFF, a slight current still +60C +140FAccessories included with the receiver Qty Supplied AccessoriesTable of Contents Battery installation Accessory AttachmentAntenna Belt clipPanel description Panel DescriptionMode Switch Mode SET VFO/MEMORY Switch V/M SkipMonitor Switch SQL ATT External DC Power Jack DCFunction display Battery Indicators Skip Scan Indicator pgs2ATTENUATOR Indicator p Audio and video output jack informationDual LCD What is VFO? Frequency and Channel SettingVFO and memory channels Operating band selectionSetting a tuning step Setting a frequencySelecting a memory channel Push SQL ATT to exit the attenuator setting conditionAttenuator function Lock functionBasic Operation When a signal is receivedReceiving U.S.A. version automatically turns itself OFF whenSetting squelch level Setting volume levelWhile pushing SQL, rotate Dial to select the squelch levelMonitor function Receive mode selectionPush Func + Mode SET momentarily to enter set mode Setting the backlighting conditionDisplay backlighting Rotate Dial until Light appearsMemory Channels Memory channel contentsGeneral Programming during selectionProgramming after selection Transferring memory contents to another memoryPush Func + V/M for 2 sec. to clear Memory bank selection Memory clearExample Clearing memory channel 3 memory bank a Memory names Rotate the tuning dial to select the desired characterScan types Scan OperationFull Scan p Function pRelease ↔ to start the scan Full/band/programmed scanTo stop the scan, push ↔ again Memory bank scanBand ranges Selecting scan edgesSetting the scan pause time Skip channel settingScan resume condition Rotate Dial until Pause Scan or Pause appearsRotate Dial until Scan Resume or RESUmE appears Setting the scan resume timeProgramming a skip frequency Frequency skip functionFrequency skip function ON/OFF Priority watch types Priority WatchMemory Scan Watch p VFO Scan Watch pPriority watch operation Push Mode SET to exit set mode and start the watchMemory channel watch and memory scan Watch Rotate Dial to select Priority or PRIoVFO scan watch Subaudible Tone Operation Setting subaudible tones for tone squelch OperationTone squelch operation OperationRotate Dial until Tone Freq. or tonE appears Pocket beep operationAvailable subaudible tone frequencies Unit Hz Push SQL to stop the beeps and flashing Tone scanPush ↔ to stop the scan Duplex shift direction Duplex OperationRotate Dial until Duplex or dUP appears Rotate Dial until Offset Freq. or oFFSEt appears Offset frequencyRange, if desired Band ScopeTV Operation Skip channel settingTV operation TV channel receivingTV frequency AM TV memory channel TV frequency AM TV receivingPush ↔ one or more times to select the band above 30 MHz Push Func + one or more times to select the TV screenATV operation Sub carrier adjustmentATV memory channel Signal levels Signal sourceDirection Finding Direction finding function exampleSet mode items Set modeOther Functions Dial select step Setting dial select stepRelease Func to exit the condition Rotate Dial until A.Power OFF or AP oFF appears Auto power-off functionBeep tones Rotate Dial until Beep Audio or bEEP appearsMonitor switch action Power saverRotate Dial until Power Save or P Save appears Rotate Dial until Monitor or monI appearsLock function effect Dial speed accelerationRotate Dial until Dial Speedup or SPEEd appears Rotate Dial until Key Lock or LoCk appearsColor LCD can be automatically turned on when using Display mode selectionDisplay contrast Rotate Dial until Display or dISP appearsDisplay background color Display brightnessRotate Dial until Bright appears Total reset Partial resetPush Power for 2 sec. to turn power OFF Cloning functionBattery cautions Battery ChargingBattery charging Battery pack installationTurn power OFF Check CP-18A/E fuse ReplacementCP-18A/ERegular charging Rapid charging with the BC-135Memory mode VFO mode Operation Flow ChartAuto power OFF p Confirmation beep p Backlighting p Power save pScan resume time p A. channels TV Frequency TableCcir channels Taiwan channels Australian channelsNew Zealand channels Indonesian channels China channelsItalian channels FOT channels General Specifications and OptionsReceiver Options Operating periods ApproxProblem Possible Cause Solution TroubleshootingQuick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan